Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1. Convert:

(a) 153.53 from decimal to octal.

(b) 2B.C4 from hexadecimal to decimal.

(c) 2AB from hexadecimal to binary.

(d) 545 from octal to hexadecimal.

(e) 127.54 from octal to decimal.

2. What are Universal gates? Realize different Logic gates using Universal gates only.

3. Describe Full Adder. Provide design of a Full Adder. Realize a full Adder using NAND gates only.

4. a. Simplify: F = AB+A(B+C)+B(B+C).

5. Describe in detail classification and characteristics of memories.

6. How can you realize edge triggered JK flip flop from an SR flip flop? Provide its truth table and describe how race around problem is removed in it?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M99450

Have any Question? 


Related Questions in Electrical & Electronics

1 the tank is accelerated upward at a uniform rate does the

1. The tank is accelerated upward at a uniform rate. Does the manometer level go up or down? 2. Glass viewing windows are to be installed in an aquarium. Each window is to be 0.6 m in diameter and to be centered 2 m belo ...

1 why is it that the distances r1 and r2 in the phase

1. Why is it that the distances r 1 and r 2 in the phase factors in equations (8.47a) and (8.47b) cannot be set equal to r, but the same quantities in the amplitude factors can be set equal to r? 2. What is an array fact ...

A compute and plot the impulse response of the systemb

a. Compute and plot the impulse response of the system. b. Compute and plot the step response of the system. c. Compute and plot the response of the system to the input signal

A clean 15--efficient module stc 1 m2 in size has its own

A clean, 15-%-efficient module (STC), 1 m 2 in size, has its own 90% effi- cient inverter. Its NOCT is 44° C and its rated power degrades by 0.5%/° C above the 25° C STC. a. What would its STC rated power be? b. Find the ...

Assignment projecttitle design of control

Assignment: Project Title: Design of Control Systems Problem: Design a closed-loop controller for a servo system (motor) with tachometer feedback. The output; c(t), corresponds to the position of the motor, while the tac ...

1 what is the particular advantageous characteristic

1. What is the particular advantageous characteristic associated with the unit vectors in the Cartesian coordinate system? 2. How do you find a vector perpendicular to a plane? 3. How do you find the perpendicular distan ...

Assume an image uses a palette of size 8 out of the table

Assume an image uses a palette of size 8 out of the table used by JPEG (GIF uses the same strategy, but the size of the palette is 256), with the combination of the following colors with the indicated level of intensitie ...

1 what is the difference between dm and dpcm2 what is the

1. What is the difference between DM and DPCM? 2. What is the problem with a speech signal that is compressed using the LPC method? 3. In transform coding, when a sender transmits the M matrix to a receiver, does the sen ...

Your client wants a quick design for a system to pump on

Your client wants a quick design for a system to pump on the order of 1800 gallons per day from a depth of 200 ft. You decide to use a 45-V submersible pump with an estimated efficiency of 35% along with PV modules havin ...

Figure 3013 shows a router using priority queuing at the

Figure 30.13 shows a router using priority queuing at the input port. The arrival and required service times (transmission time is negligible) for 10 packets are shown below; ti means that the packet has arrived i ms aft ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro