Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) describe the use of 8251 chip.

2) prepare down the various types of methods used for data transmission?

3) What are the different programmed data transfer methods?

4) What do you mean by synchronous data transfer?

5) What do you mean by asynchronous data transfer?

6) What are the functional types used in control words of 8251?

7) What are the basic modes of operation of 8255?

8) prepare down the features of mode 0 in 8255.

9) What are the features which are used in mode 1 in 8255?

10) What are the signals used in input control signal & output control signal?

11) prepare down the features used mode 2 in 8255?

12) What are the various types of prepare operations used in 8253?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M910957

Have any Question? 


Related Questions in Electrical & Electronics

A three-phase induction motor is required to operate from a

A three-phase induction motor is required to operate from a single-phase source. One possible connection is shown in Figure P18.28. Will the motor work? Explain why or why not.

A vehicle driver gauges the relative speed of a preceding

A vehicle driver gauges the relative speed of a preceding vehicle by the speed with which the image of the width of that vehicle varies. This speed is proportional to the speed X of variation of the angle at which the ey ...

For the network of given figurea find the currents

For the network of given figure: a. Find the currents I 1  and I s . b. Find the voltages V s  and V 3 .

Using mesh analysis determine i5omeganbspand vanbspfor the

Using mesh analysis, determine I 5Ω  and V a  for the network of given figure.

Figure 227 shows a simple mechanical system consisting of a

Figure 2.27 shows a simple mechanical system consisting of a mass, spring and damper. Derive a mathematical model for the system, determine the transfer function, and draw the block diagram

A motor is supplying 50 n times m of torque to its load if

A motor is supplying 50 N × m of torque to its load. If the motor's shaft is turning at 1500 r/min, what is the mechanical power supplied to the load in watts? In horsepower?

A 200v dc motor is loaded by a constant torque of 10 nm the

A 200V dc motor is loaded by a constant torque of 10 NM. The armature resistance of the motor is 2Ω, and the field constant Kφ=2.5V s. Calculate the motor speed.

Determine the value of the resistance r which results in a

Determine the value of the resistance R which results in a current of A emerging from the positive terminal of the dependent voltage source in the circuit shown in Figure P8-6.

Write the answer of the given questionan overhead

Write the answer of the given question: An overhead transmission line conductor having a parabolic configuration weighs 1.925 kg/cm 2 per metre of the length .The area of X-section of the conductor is 2.2 cm 2 and the ul ...

A spooling system figure 616 consists of an input process i

A spooling system (Figure 6.16) consists of an input process I, a user process P, and an output process O connected by two buffers. The processes exchange data in blocks of equal size. These blocks are buffered on a disk ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

A cola-dispensing machine is set to dispense 9 ounces of

A cola-dispensing machine is set to dispense 9 ounces of cola per cup, with a standard deviation of 1.0 ounce. The manuf

What is marketingbullwhat is marketing think back to your

What is Marketing? • "What is marketing"? Think back to your impressions before you started this class versus how you

Question -your client david smith runs a small it

QUESTION - Your client, David Smith runs a small IT consulting business specialising in computer software and techno

Inspection of a random sample of 22 aircraft showed that 15

Inspection of a random sample of 22 aircraft showed that 15 needed repairs to fix a wiring problem that might compromise

Effective hrmquestionhow can an effective hrm system help

Effective HRM Question How can an effective HRM system help facilitate the achievement of an organization's strate