Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

problem 1: List and describe four different kinds of layouts for a factory.

problem 2: Two machining operations, A (3 minutes per part) and B (10 minutes per part), are performed sequentially to manufacture a part. Machines A and B produce 5% and 6% defective items, correspondingly. The factory operates 8 hours each day, 5 days per week, and 4.2 weeks per month. Every day each machine requires 0.30 hour for being set up. Find the machine fraction for each type (A and B) if we require to handle a demand of 1000 items per month. Use a machine-up factor equal to 85% for each machine.

380_machine performed sequentially.jpg

problem 3: A manufacturing facility comprises of five departments 1, 2, 3, 4 and 5. It produces four components having the manufacturing product routings and production volumes indicated in the table below.

a) Generate a from-to chart.

b) Find a relationship chart by using the given rules: “A” for 85-66 trips between departments, “E” for 65-46, “I” for 45-26, “O” for 25-6, and “U” for 5-0.

c) Find out closeness ranks.

1775_closeness ranks.jpg

problem 4: What are the primary benefits of using computerized layout procedures versus Systematic Layout Planning (SLP) procedures done by hand?

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M91802

Have any Question? 


Related Questions in Civil Engineering

Literature reviewwhat is waste paper ashis a waste material

LITERATURE REVIEW What is Waste Paper Ash? Is a waste material collected from the Paper Industry How is it generated? Why I want to use it as replacement to cement ? Effect of strength & workability for WPA , FA, SA, WA ...

An n-bit updown counter is a sequential circuit with a

An N-bit up/down counter is a sequential circuit with a clock input and an up/down control input. Wen control is 1, the circuit counts up, modulo 2N, on each rising edge of the clock. In other words, the present-state ou ...

For fully developed laminar pipe flow in a circular pipe

For fully developed laminar pipe flow in a circular pipe, the velocity profile is given by u(r) = 2(1 - r 2 /R 2 ) in m/s, where R is the inner radius of the pipe. If the pipe's inner diameter is 4 cm, find the maximum a ...

Based on the values you calculated in problem 208 answer

Based on the values you calculated in Problem 20.8, answer and explain the following: a. In which vessels should elasticity of the vessel be considered? b. In which vessels should the non-Newtonian behavior of blood be c ...

Ben bitdiddle is exploring finite-state machines of the

Ben Bitdiddle is exploring finite-state machines of the following form: A. Draw a state-transition diagram for the FS . Assume that you start in the state Q0 = 0, output = 1. B. Assume that you start in the state Q0 = 0, ...

The step response of a linear circuit isa is the circuit a

The step response of a linear circuit is (a) Is the circuit a low-pass, high-pass, bandpass, or bandstop filter? (b) Construct the straight-line Bode gain plot and estimate the cutoff frequency and passband gain. (c) Use ...

Is it possible to assign valid logic levels and noise

Is it possible to assign valid logic levels and noise margin boundaries so that a device with the following transfer characteristic would serve as an inverter? Briefly explain your reasoning

1 draw a state-transition diagram for an fsm that

1. Draw a state-transition diagram for an FSM that recognizes strings denoted by the regular expression A*BB*C 2. Draw the state-transition diagram for a deterministic FSM that recognizes the strings AI(AB). Take care no ...

If the uncertainties in temperature and pressure for prob

If the uncertainties in temperature and pressure for Prob. 7.49 are ±1.5?F and ±2 kPa, respectively, what is the uncertainty of the billing if the actual volume flow measurement is exact? Prob. 7.49 A positive-displaceme ...

Suppose that we have the following three reference patterns

Suppose that we have the following three reference patterns and their targets: The probability of vector p1 is 0.25, the probability of vector p2 is 0.25 and the probability of vector p3 is 0.5. i. Draw the network diagr ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen