Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Please prepare a paragraph or two using your own words on the given problems:

problem: What are the multipoint constraints?

problem: What is the main difference between an RBE2 and RBE3? When is one use over the other?

problem: What is the basic difference between an isotropic, orthotropic and anisotropic material?

problem: What is the major difference between finite elements, finite difference, and finite volume?

problem: What are stability, consistency and convergence of a difference equation?

problem: What is the difference between linear models versus nonlinear model?

problem: What is the difference between an explicit method over implicit in FEA? Which one will you use over the other? Name the type of analysis.

problem: What is the Newton Raphson method? How does it work?

problem: What is the difference between bonded contact and standard contact? Which one can model friction effects?

problem: What is the difference between the von-mises and maximum principal stress?

problem: What is axisymmetric, plane stress, and plane strain modeling?

problem: What is difference between a beam, spar, shell, and solid element? Give an explanation on when you will use either elements?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M9197

Have any Question? 


Related Questions in Mechanical Engineering

The velocity profile in the annular control volume of

The velocity profile in the annular control volume of Example is approximately linear, varying from a velocity of zero at the outer boundary to a value of ωd/2 at the inner boundary. Develop an expression for the fluid v ...

The doctoral candidate phd research is entitled a critical

The Doctoral Candidate PhD research is entitled "A critical Investigation of Risk Management Practices Influence on the Pharmaceutical Supply Chain Performance" The focus of this dissertation is thus on the risk manageme ...

Heat transfer problem -a thermocouple is to be utilized to

Heat Transfer Problem - A thermocouple is to be utilized to measure the temperature of exhaust gases from an automobile engine and the effect of the cylindrical radiation shield installed as shown in the image, is to be ...

A dilute suspension contains ten spheres per liter a sample

A dilute suspension contains ten spheres per liter. A sample (one tenth of that solution) is removed. What is the probability that there is (a) at least one sphere, (b) at most one sphere in the sample. You may assume th ...

Two small cubes of equal size but made of different

Two small cubes of equal size but made of different materials are stacked (as shown in the figure below), so they just fit between two rigid surfaces. The bottom cube is subjected to a uniform pressure p on each of its e ...

1 determine the capillary rise for a water-air-glass

1. Determine the capillary rise for a water-air-glass interface at 40°C in a clean glass tube having a radius of 1 mm. 2. Determine the difference in pressure between the inside and outside of a soap film bubble at 20 °C ...

1 water is flowing through a large circular conduit with a

1. Water is flowing through a large circular conduit with a velocity profile given by the equation v = 9(1- r 2 /16) fps. What is the average water velocity in the 1.5-ft pipe? 2. Water enters a 4-in. square channel as s ...

1 the following data define the sea-level concentration of

1) The following data define the sea-level concentration of dissolved oxygen for fresh water as a function of temperature: T 0 8 16 24 32 40 01F 14.64 11.85 9.87 8.41 7.30 6.43 Use MATLAB to fit the data with (a) piecess ...

A bar consists of two portions bc and c d of the same

A bar consists of two portions BC and C D of the same material and of the same length L, but of different cross sections. Determine the strain energy of the bar when it is subjected to an axial load P, expressing the res ...

The case study kahiki-foods-case-study critique it and do a

The case study kahiki-foods-case-study CRITIQUE it and do a 10-12 pages report about it their are notes and a presentation done about it that you can use in doing the paper Also their is an example of a different case wh ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro