Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1: What are the hierarchy of visual weightage for different forms and elements in the architecture?

problem 2: Distinguish the terms unity and variety in architecture.

problem 3: What are the variable factors that affect the climate?

problem 4: What are the needs and categories of the residential buildings?

problem 5: What are the design modification which can be adopted for Hot and dry region?

problem 6: List out the significant services to be provided in a building.

problem 7: Define the term Building-by-law and what are the objects of the town planning?

problem 8: Describe the components of staircase with neat sketch.

problem 9: Describe the concept of Scales and selection of scale for Plan, Section and Elevation of a Building.

problem 10: Draw a neat sketch of a single bed room residential building showing its plan and elevation.

problem 11: Draw a neat sketch of the standard symbols and abbreviations which is used in Civil Engineering Drawing.

problem 12: describe the nature of an institutional building. What are the principles to be adopted while designing a building?

problem 13: Describe the rules to be followed for a building drawing approval.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93096

Have any Question? 


Related Questions in Mechanical Engineering

1 a venturi meter with an inlet diameter of 06 m is

1. A Venturi meter with an inlet diameter of 0.6 m is designed to handle 6 m3 /s of standard air. What is the required throat diameter if this flow is to give a reading of 0.10 m of alcohol in a differential manometer co ...

Heat transfer problem -a thermocouple is to be utilized to

Heat Transfer Problem - A thermocouple is to be utilized to measure the temperature of exhaust gases from an automobile engine and the effect of the cylindrical radiation shield installed as shown in the image, is to be ...

Draw the moment diagram for the elbow-biceps-forearm-hand

Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment if the total weight w of the forearm and hand are included and are assumed to act at the mid ...

1 write down the equations for the reverse active mode by

1. Write down the equations for the reverse active mode by inspection without doing any algebra. 2. Are there any currents flowing in the cutoff mode? What is their magnitude if there are? 3. Obtain the saturation voltag ...

During the test of a centrifugal pump a bourdon pressure

During the test of a centrifugal pump, a Bourdon pressure gage just outside the casing of the 12-in.-diameter suction pipe reads 6 psig (i.e., vacuum). On the 10-in. -diameter discharge pipe another gage reads 40 psig. T ...

1 according to the equipartition principle what is the

1. According to the equipartition principle, what is the overall energy in J of one mole of water at 1000 K if translational, rotational, and vibrational degrees of freedom are considered? 2. How many equipartition degre ...

An open tank l ft long as shown below travels to the right

An open tank L ft long as shown below travels to the right at a velocity v c  fps. A jet of area A j  exhausts fluid of density r at a velocity v j  fps relative to the car. The tank car, at the same time, collects fluid ...

Suppose that the performance of a bjt transistor is

Suppose that the performance of a BJT transistor is entirely limited by emitter injection efficiency, which limits the d.c. beta, and base spreading resistance, which limits the bandwidth. Show that the gain-bandwidth pr ...

A prototype bolt shaft assume a uniform cylinder that is to

A prototype bolt shaft (assume a uniform cylinder) that is to be loaded in tension is made of a stainless steel with a yield strength of 450 MPa and has a safety factor of 3 with respect to yielding for the maximum allow ...

Projectdesign a tube bank that will increase the

Project Design a tube bank that will increase the temperature of a 1200 CFM flow of air from 35°F to 100°F. Assume a constant pressure of 1atm. Each tube will have a diameter of 0.5in and a length of 24in. The tube confi ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro