Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) prepare down the advantages of electric heating?

2) prepare down the properties of heating element that you will look for?

3) Describe the advantages of induction heating.

4) prepare down advantages and disadvantages of direct and indirect arc furnace.

5) Describe performance of different electrodes used in electric arc furnace?

6) Describe how high frequency supply is obtained?

7) What are the different types of electric arc welding?

8) What do you mean by resistance welding?

9) What is meant by welding?

10) prepare down the various kinds of electric welding?

11) Describe clearly pinch effect in detail.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911480

Have any Question? 


Related Questions in Mechanical Engineering

The space between two very long parallel plates separated

The space between two very long parallel plates separated by a distance h is filled with a fluid with viscosity where μ0 is a constant and n is a constant exponent. The top plate slides to the right with a constant speed ...

For the allen wrench of problem 715 what is the deflection

For the allen wrench of Problem 7.15, what is the deflection of the tip of the wrench when the maximum load of 60 N is applied, just before the bolt loosens? Problem 7.15: The maximum force applied to the tip of the alle ...

1 a cylindrical pressure vessel with hemispherical endcaps

1. A cylindrical pressure vessel with hemispherical endcaps has radius r = 2 m, wall thickness t = 10 mm, and is made of steel with yield stress σy = 1800 MPa. It is internally pressurized at p = 2 MPa. Compare the Tresc ...

1 what requirements control the derivation of load-stress

1. What requirements control the derivation of load-stress relations? 2. Describe the method of mechanics of materials. 3. How arc stress-strain-temperature relations for a material established? 4. Explain the difference ...

A typical engine alternates between compression and

A typical engine alternates between compression and expansion of a gas. If during the compression stroke the entropy of the gas is reduced by 0.20JK -1 , what is the minimum change to the entropy of the surroundings?

The top figure shows a diagram of the bones and biceps

The top figure shows a diagram of the bones and biceps muscle of a person's arm supporting a mass. The lower figure shows a biomechanical model of the arm, in which the biceps muscle AB is represented by a bar with pin s ...

Water flows steadily through the piping junction entering

Water flows steadily through the piping junction, entering section 1 at 0.0013 m 3  /s. The average velocity at section 2 is 2.1 m/s. A portion of the flow is diverted through the showerhead, which contains 100 holes of ...

A simply supported beam of length l is subjected to loads

A simply supported beam of length L is subjected to loads that produce a symmetric deflection curve with maximum deflection at the midpoint of the span. How much strain energy U is stored in the beam if the deflection cu ...

A compute the intrinsic gate delay of the nmost given in

(a) Compute the intrinsic gate delay of the nMOST given in the above problem and also in section 661 at the biasing condition given above. (b) Compute the intrinsic power-delay product. (c) Does the load resistor increas ...

1 the dam shown below is 100 m wide determine the magnitude

1. The dam shown below is 100 m wide. Determine the magnitude and location of the force on the inclined surface. 2. The float in a toilet tank is a sphere of radius R and is made of a material with ρ. An upward buoyant f ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen