Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1: Describe the given terms:

a) Beam area.
b) Radiation intensity.
c) Beam efficiency.
d) Directivity.

problem 2: Describe the radiation from two-wire.

problem 3: Define the following terms:

a) Bandwidth.
b) Polarization.
c) Effective aperture area.
d) Beam width.

problem 4: Find out the effective length of a half-wave dipole?

problem 5: prepare brief note on the small loops.

problem 6: What are the different merits and demerits of loop antennas?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M93524

Have any Question? 


Related Questions in Electrical & Electronics

Power mosfet breakdown voltage 800v must conduct 10a when

power mosfet breakdown voltage 800v must conduct 10A when on with a maximum on state voltage 4v.If the current density in the mosfet must be limited to 200A/cm,estimate the conduxting area

1 what is the expansion for the divergence of a vector2

1. What is the expansion for the divergence of a vector? 2. State Gauss' law for the magnetic field in differential form. How is it derived from its integral form? 3. How can you determine if a given vector can represent ...

1 in kademlia assume m 4 and active nodes are n4 n7 and

1. In Kademlia, assume m = 4 and active nodes are N4, N7, and N12. Where is the key k3 stored in this system? 2. In Chord, assume the size of the identifier space is 16. The active nodes are N3, N6, N8, and N12. Show the ...

Repeat problem with the elastic constants of the plastic

Repeat Problem with the elastic constants of the plastic defined as E = 10 GPa and ν = 0.485. Problem:- A rectangular plastic specimen of size 100 X 100 X 10 mm 3  is placed in a rectangular metal cavity. The dimensions ...

A clean 15--efficient module stc 1 m2 in size has its own

A clean, 15-%-efficient module (STC), 1 m 2 in size, has its own 90% efficient inverter. Its NOCT is 44° C and its rated power degrades by 0.5%/° C above the 25° C STC. a. What would its STC rated power be? b. Find the k ...

Solve problem using the secant method do not use the

Solve Problem using the secant method. Do not use the incremental force method. Discuss about the convergence rate. Problem :- Consider a uniform bar with a constant Young's modulus, E = 100 MPa; cross-sectional area, A ...

1 for the force field f x2ay find the approximate value of

1. For the force field F = x 2 ay, find the approximate value of the line integral of F from the origin to the point (1, 3, 0) along a straight line path by dividing the path into ten equal segments. 2. For the force fie ...

In problem find the rate of discharge if the frictional

In Problem , find the rate of discharge if the frictional head loss in the pipe is 3.2 v2 /g where v is the flow velocity in the pipe. Problem:- Referring to the figure, assume the flow to be frictionless in the siphon. ...

1 discuss the application of the gradient concept for the

1. Discuss the application of the gradient concept for the determination of unit vector normal to a surface. 2. How would you find the rate of increase of a scalar function along a specified direction by using the gradie ...

1 derive the weak form of a two-dimensional steady-state

1. Derive the weak form of a two-dimensional, steady-state heat transfer problem. 2. Derive the weak form of a simply supported beam problem.

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro