Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

What do you understand by the term stainless steels? Provide typical composition, applications and properties, of all kinds of stainless steels. Why these steels are stainless? Discuss.

problem 2:

What do you understand by the term thermomechemical processing? Illustrate in detail. What are the advantages? Which super alloys are subjected to the thermomechamical treatment? Illustrate in detail.

problem 3:

Illustrate the various techniques accessible for degassing the dissolved gases from molten super alloys.

problem 4:

Illustrate in detail the typical heat treatment processes adopted to wrought super alloys so as to alleviate the structure sufficiently to generate optimized long time rupture properties.

problem 5:

What are the advantages and drawbacks of visual test technique? Illustrate.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911243

Have any Question? 


Related Questions in Mechanical Engineering

1 why are micropower plants so different from larger ones

1. Why are micropower plants so different from larger ones? In what cases are they recommended? 2. Discuss which of the conventional alternative sources of energy is more suitable for use with induction generators to pro ...

1 the hypodermic needle shown below contains a liquid serum

1. The hypodermic needle shown below contains a liquid serum (ρ = 1 g/cm 3 ). If the serum is to be injected steadily at 6 cm 3  /s, how fast should the plunger be advanced (a) if leakage in the plunger clearance is negl ...

1 by how much will the clamping force on the joint be

1. By how much will the clamping force on the joint be reduced? Sketch the new joint diagram, assuming maximum initial preload? Compute the estimated maximum bolt tension and minimum clamping force under the 3,000 lbs ex ...

I need a proposal project for surface metrology asap i need

I need a proposal project for Surface Metrology ASAP. I need two documents: 1. Project outlines Proposal outlines (the instruction & template is in the attached Proposal for the project) should be 1 page 2. Final project ...

A sample of he ions is prepared at a temperature of 298 k

A sample of He + ions is prepared at a temperature of 298 K and a density of 2.0 # 10 10 cm -3 . Because these are ions, magnetic ields may be used to trap those ions with kinetic energy less than some threshold value et ...

A room has design conditions of78 f db and 50 rh and a rscl

A room has design conditions of78 F DB and 50% RH and a RSCL = 18,000 BTUlhr and RLCL = 8000 BTUlhr. An air conditioning unit supplies 900 CFM of air to the room at 58 F DB and 56 F WB. Will the unit maintain the room de ...

If the speed of the shaft is doubled in given problem what

If the speed of the shaft is doubled in given Problem, what will be the percentage increase in the heat transferred from the bearing? Assume that the bearing remains at constant temperature. Problem An automobile cranksh ...

Health and safety management 1 the following gas

Health and Safety Management 1. The following gas detector tubes are available for direct reading of concentrations of the toxic gas hydrogen sulfide Tube Concentration 4HT 1-40% 4HH 0.1-4.0% 4H 10-3200 ppm 4M 12.5-500 p ...

A beam with a rectangular cross section has dimensions as

A beam with a rectangular cross section has dimensions, as defined in Fig. 8.13, of b = 40and t = 10 mm. The beam is made of 7475-T7351 aluminum and is subjected to a bendingmoment of M = 900 N·m. (a) If a through-thickn ...

Two structural steel shafts with flanges forged on their

Two structural steel shafts with flanges forged on their ends are rigidly connected with a circle of bolts. The shafts are meant to rotate in their supports at A and D, however a 100 N · m torque is applied to flange B w ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen