Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

problem 1: What is meant by 33, 43 and 53 grades of cement?
 
problem 2: describe the pozzolonic reactions in concrete? describe the function of gypsum in cement?
 
problem 3: What are pozzolonas? Describe the pozzolonic reactions in concrete? List out the common pozzolona used in concrete?

problem 4: What is hydration of cement? Describe the function of all thy-Bogues compounds in the hydration of cement?

problem 5: How the initial setting time of cement is determined? Describe the significance of initial and final setting time of cement?

problem 6: prepare a short notes on:

a) High strength concrete.
b) Fibre reinforced concrete
c) Light weight concrete

problem 7: Discuss the various objectives of using admixtures in concrete. What are the various types of admixtures?

problem 8: What are chemical admixtures? describe the usage of any three of them in detail.
 
problem 9:

a) prepare short notes on Light weight concreteWhat are the different types of fibres used in concrete?
b)Mention the relative merits and demerits of each type.
 
problem 10: What is meant by segregation and bleeding?

problem 11: What is workability of concrete? Discuss the various methods by which workability of concrete is measured?
 
problem 12: What are the different methods of curing of concrete? Mention merits and demerits of each type.
 
problem 13: describe bulking of sand. How does it affect the quantity of sand in volume batching?

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M93471

Have any Question? 


Related Questions in Civil Engineering

An edge-triggered flip-flop 8lsquo1 has setup and hold

An edge-triggered flip-flop 8‘1 has setup and hold times of t, and th, respectively. The flip-flop 8'2 is constructed by adding a delay of td to the data input of 8'1. (Consider a delay to be a buffer with t pd = t cd = ...

The homogeneous cylinder of weight w and radius r rests in

The homogeneous cylinder of weight W and radius R rests in a groove of width 2b. Determine the smallest force P required to roll the cylinder out of the groove. Assume that there is enough friction to prevent slipping.

1 is it possible for a one-input one-output combinational

1. Is it possible for a one-input, one-output combinational circuit built entirely of two-input NAND gates to contain a hazard? Either draw such a circuit or explain why one cannot be built. 2. Is it possible for a Combi ...

The magnitude of the force f acting at point a on the plate

The magnitude of the force F acting at point A on the plate is 160 kN. Determine the equivalent force-couple system with the force acting at point O.

Repeat exercise e71 using the pseudoinverse ruleexercise

Repeat Exercise E7.1 using the pseudoinverse rule. Exercise E7.1 Consider the prototype patterns given to the left. i. Are p 1 and P 2 orthogonal? ii. Use the Hebb rule to design an autoassociator network for these patte ...

An n-bit updown counter is a sequential circuit with a

An N-bit up/down counter is a sequential circuit with a clock input and an up/down control input. Wen control is 1, the circuit counts up, modulo 2N, on each rising edge of the clock. In other words, the present-state ou ...

The breaking strength of the cable fg that supports the

The breaking strength of the cable FG that supports the portable camping stool is 400 lb. Determine the maximum weight W that can be supported. Neglect friction and the weights of the members.

Suppose you are shown this circuitwithout any analysis-just

Suppose you are shown this circuit: Without any analysis-just by looking at the circuit-you should be able to tell whether it does or does not have a hazard. Explain how you can do this and indicate whether or not this c ...

1 what is the meaning of the term structural i how is it

1. What is the meaning of the term STRUCTURAL I? How is it used? 2. What are the veneer grades? Which veneers are the more similar in appearance and surface qualities? Which veneers are structurally more similar? State t ...

Consider the three prototype patterns shown in figure e72i

Consider the three prototype patterns shown in Figure E7.2. i. Are these patterns orthogonal? Demonstrate. ii. Use the Hebb rule to determine the weight matrix for a linear autoassociator to recognize these patterns. iii ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro