Weldments amp sheet metalinstructions use sheet metal and, Ask an Expert

Engineering

WELDMENTS & SHEET METAL

INSTRUCTIONS: Use Sheet Metal and Weldments to create the assembly file shown in FIGURE in attachment file

Create the weldment as a part file shown in FIGURE HW#1-1 using the instructions per exercise MCE181-CE#1 WELDMENTS. Use the 3D sketch shown in FIGURE HW#1-2 for dimensions. The structural members are 4"x4"x0.25" square tubes and the joints must be trimmed/extended as shown. See FIGURE HW#1-4 for additional views on the joints.

Add weldment end caps and 4 gussets with fillets as shown.

Create an assembly file, import the weldment, and create the sheet metal as shown in FIGURE HW#1-1. Side panels must be removable and the top and back panels must be welded. For removable panels, use the hole series and smart fastener tools for ½-13 flatheads. Follow exercise MCE181-CE#2 SHEET METAL for design and dimensional instructions on removable sheet metal, welded sheet metal, hole series, and smart fasteners.

Remove tangent edges, keep origin planes on center, and fully define the 3D sketch. The file should not have any unsolvable or conflicting entities(yellow or red under the design tree).

Attachment:- WELDMENTS&SHEET METAL.rar

View complete question

Mechanical Engineering, Engineering

Category:- Mechanical Engineering
Reference No.:- M91670684

Have any Question?Write your Review or question?

Related Questions in Mechanical Engineering

Alocate ten minutes for the presentationuse audio visual

Allocate ten minutes for the presentation Use audio / visual / technological supports / aids where appropriate Use a minimum of 3 properly referenced articles. THEMES PRESENTATION TOPIC MEMORY Discuss the three learning ...

Assignment -q1 explain the difference between the

Assignment - Q1. Explain the difference between the metacentric height of a ship during 'Partially Afloat condition and 'Free Floating' condition; aid a sketch to support your answer. Q2. With the aid of sketches, explai ...

Mechanical engineering assignment task - solve the given

Mechanical Engineering Assignment Task - Solve the given problem. Task 1 - A spring with a one-turn loop of 40mm mean radius is formed from a round section of wire having 5 mm diameter. The straight tangential legs of th ...

Force exerted by jet on moving cart1 you need to determine

Force Exerted By Jet On Moving cart. 1. You need to determine the velocity of water that comes out from the nozzle of this system. need the equation please formulate the equation. 2. This water will strike a small cart a ...

Structural mechanics questions -q1 a 150-lb bucket is

Structural Mechanics Questions - Q1. A 150-lb bucket is suspended from a cable on the wooden frame. Determine the resultant internal loadings on the cross section at D, and at E. Q2. The shaft is supported at its ends by ...

Life cycle assessmentfor your chosen service eg white

LIFE CYCLE ASSESSMENT For your chosen service (e.g. white board markers), identify two alternatives of getting the service (e.g. brand A, brand B). Choose the most environmentally friendly option by conducting life cycle ...

Fluid mechanics assignment - finite control volume analysis

Fluid Mechanics Assignment - Finite Control Volume Analysis and Dimensional Analysis Q1. The wind blows through a 7ft × 10ft garage door opening with a speed of 5 ft/s as shown in the figure. Determine the average speed, ...

Questions -q1 a qualitative estimate of the effect of a

Questions - Q1. A qualitative estimate of the effect of a wind-tunnel contraction (Figure) on turbulent motion can be obtained by assuming that the angular momentum of eddies does not change through the contraction. Let ...

5star questions amp answers1a define heat treatment bname

5 STAR QUESTIONS & Answers 1. A) Define Heat treatment B) Name different types of heat treatment processes C) Write any 4 purposes of Heat treatment 2. Explain various Heat treatment processes 3. A) Compare Thermo plasti ...

1 explain the term critical equipment and provide two clear

1. Explain the term "critical equipment" and provide two clear examples of machinery which falls into this category on board a twin screw motor vessel. 2. Explain the process of Charpy lmpact Testing including sample mar ...

4,153,160 Questions Asked
13,132 Experts
2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Recent Questions

Ask Mechanical Engineering Expert