Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1: A truss is shown in the given figure. find out the horizontal deflection of joint D produced by  both  the  load  and  fabrication  error  (bar  AE  is  40mm  too  long).  For all bars, area A = 1000 mm2, E = 200 GPa.

2102_horizontal reflection.jpg

problem 2: Use the Force Method to find out all the support reactions in the given figure. A is a fixed support and B and C are roller supports. EI is constant.

1840_force method.jpg

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M9769

Have any Question? 


Related Questions in Mechanical Engineering

Many devices have been developed to measure the viscosity

Many devices have been developed to measure the viscosity of fluids. One such device, known as a rotational viscometer, involves a pair of concentric cylinders with radii r i and r o , and total length L. The inner cylin ...

Figure a shows a steel i-beam cross section note not

Figure (a) shows a steel I-beam cross section (note, not symmetric about the y axis). Two steel plates with cross section 10 mm × 200 mm are welded to the beam. Figure (b) and the 3D inset show the configuration of the c ...

If all the states of an ensemble are equally probable then

If all the states of an ensemble are equally probable, then a 0.05 mol sample of an ideal gas at ixed energy in a 1000 cm3 container has a chance of being found in a state where a speciied 1% region of the volume is not ...

For the experimental pump data given belowqflow rate

For the experimental pump data given below: Q F low Rat e ( ???? /s) ???? Total Pressure (kPa) P IN Shaft power (kW) 0.0000 504.82 1.190 0.0004 481.50 1.318 0.0008 476.70 1.573 0.0012 471.50 1.828 0.0017 461.00 2.083 0.0 ...

1 how large as a fraction of the supported weight w must

1. How large (as a fraction of the supported weight W) must the weight w of the forearm and hand be to change the analysis done under the assumption of weightlessness? 2. What sort of simple measurement or experiment cou ...

The lateral base resistance is a fundamental limitation of

The lateral base resistance is a fundamental limitation of high-frequency and high speed performance of BJTs. At low temperatures, deionization of the dopant impurity could increase the base resistance much more than the ...

1 write down the equations for the reverse active mode by

1. Write down the equations for the reverse active mode by inspection without doing any algebra. 2. Are there any currents flowing in the cutoff mode? What is their magnitude if there are? 3. Obtain the saturation voltag ...

In problem above find the depth at which the net force on

In Problem above, find the depth at which the net force on the tank is zero. Problem :- On a certain day the barometric pressure at sea level is 30.1 in. Hg, and the temperature is 708F. The pressure gage in an airplane ...

Problem -an aluminum extrusion was created in the shape at

Problem - An aluminum extrusion was created in the shape at the right as shown with the origin at the lower left corner. Show all work in finding the centroid (4). Find moments of inertia with respect to the x and y axes ...

Imagine a set of three n2 molecules frozen in a crystal so

Imagine a set of three N2 molecules frozen in a crystal so that no rotation or translation can occur. But there is energy in vibration, which totals E = 3ve , where the vibrational constant e = 2358cm-1 . If we apply the ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen