Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

Objective: To provide knowledge and practice AutoCAD software package for engineering activities.

Task: As a professional Engineer, you have been assigned by your company to prepare an engineering drawing for a bungalow project. You are required to prepare the engineering drawing regarding to your project and you should provide the following information.

1)    Plan View

2)    Front View

3)    Rear View

4)    Dimension

5)    Title block

Report: Project and report is individual. Your report must be written in English. Report must include the objective, introduction, procedure (AutoCAD commands), drawings and summary. Drawing should be printed in A3 size.

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M91699

Have any Question? 


Related Questions in Civil Engineering

An lvq network has the following weightsi how many classes

An LVQ network has the following weights: i. How many classes does this LVQ network have? How many subclasses? ii. Draw a diagram showing the first-layer weight vectors and the decision boundaries that separate the input ...

1 is it possible for a one-input one-output combinational

1. Is it possible for a one-input, one-output combinational circuit built entirely of two-input NAND gates to contain a hazard? Either draw such a circuit or explain why one cannot be built. 2. Is it possible for a Combi ...

Given an n-state fsm and an m-state fsm what is the maximum

Given an n-state FSM and an m-state FSM, what is the maximum number of states possible in a circuit built from the two FSMs connected as shown below?

A water treatment plant has four clarifiers treating 80 mgd

A water treatment plant has four clarifiers treating 8.0 MGD (0.350 m 3 /sec) of water. Each clarifier is 16 ft (4.88 m) wide, 80 ft (24.4 m) long, and 15 ft (4.57 m) deep. Determine: A. The detention time (hr) B. Overfl ...

A worker applies the forces p -10i 8j lb and q 10i lb to

A worker applies the forces P = -10i + 8j lb and Q = 10i lb to the handgrips of the electric drill. These forces are equivalent to the force R = 8j lb acting at the tip of the drill and the couple C R = -120j lb · in. De ...

Is it possible to assign valid logic levels and noise

Is it possible to assign valid logic levels and noise margin boundaries so that a device with the following transfer characteristic would serve as an inverter? Briefly explain your reasoning

1 what decimal integer does the -bit 2s complement number

1. What decimal integer does the $-bit 2's complement number 11 l10101 represent? 2. A positive number is added to a negative number using 2's complement arithmetic. The result has a 1 in the sign bit. Does this indicate ...

1 devise a scheme for representing rational numbers as

1. Devise a scheme for representing rational numbers as binary strings. Briefly describe algorithms for performing addition and comparison using your scheme. 2. Devise a scheme for representing rational numbers and ratio ...

Consider again the four-class decision problem that we

Consider again the four-class decision problem that we introduced in Problem P4.3. Train a perceptron network to solve this problem using the perceptron learning rule. Problem P4.3 We have a classification problem with f ...

In this classic problem you are to design a single

In this classic problem, you are to design a single finite-state machine S that will be connected in an arbitrarily long one-dimensional string as follows: Each FSM in the string is connected by k wires to its left and r ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen