Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

V-block and clamp:

The V-block clamp comprises of 3 components, a V-block, yoke and clamping screw. By using a rule, measure the sketches below and produce a third angle projection drawing for each component.  All drawings should be fully dimensioned, with the relevant projection symbol, on a completed drawing sheet.

Point out any important tolerances for each component.

The completed two view assembly drawing is as well needed showing each component in its relevant position, with information bubbles associating to a parts list on the drawing. The parts list must point out, part name, page number, material, and number off, for each component.

Finally on a separate sheet generate a free hand sketch of the completed assembly.

Do not forget to attach the standard coversheet.

1061_Knurling.jpg

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M9300

Have any Question? 


Related Questions in Civil Engineering

1 an open-ended tube probe is oriented at an angle of 30

1. An open-ended tube probe is oriented at an angle of 30? with the flow direction in an airflow at 200 kPa and 50?C. The air velocity is 20 m/s. Calculate the pressure indicated by the probe. 2. A Pitot tube is exposed ...

1 how are the species of wood used in the fabrication of

1. How are the species of wood used in the fabrication of plywood classified? 2. The plywood in Fig. 8A has a grade stamp that indicates Group 2. Find: a. What plies in the panel contain Group 2 species? b. If not all pl ...

Consider the following state-transition diagramfor each of

Consider the following state-transition diagram: For each of the following questions, assume that the machine starts in state A. A. Give the sequence of states visited, and the sequence of outputs produced, if a machine ...

1 what are the most positive and most negative integers

1. What are the most positive and most negative integers that can be expressed using a k-bit 2's complement representation? 2. Devise a scheme for representing integers, independently of size, as binary strings. Briefly ...

Calculate the percent uncertainty in flow rate for the

Calculate the percent uncertainty in flow rate for the venturi measurements in Prob. 7.63 using the same uncertainties in the pressure and temperature measurements as in Prob. 7.62. Prob. 7.63 The airflow system in Prob. ...

Suppose that we have the following three reference patterns

Suppose that we have the following three reference patterns and their targets: The probability of vector p1 is 0.25, the probability of vector p2 is 0.25 and the probability of vector p3 is 0.5. i. Draw the network diagr ...

A baseball umpires meter has four displays balls strikes

A baseball umpire's meter has four displays: Balls, Strikes, Outs, and Inning. There are four values for the Balls display (0, 1, 2, and 3), three for Strikes (0, 1, 2), three for Outs (0, 1, 2), and ten for Inning (1, 2 ...

1 is it possible for a one-input one-output combinational

1. Is it possible for a one-input, one-output combinational circuit built entirely of two-input NAND gates to contain a hazard? Either draw such a circuit or explain why one cannot be built. 2. Is it possible for a Combi ...

Consider the three prototype patterns shown to the lefti

Consider the three prototype patterns shown to the left. i. Use the Hebb rule to design a perceptron network that will recognize these three patterns. ii. Find the response of the network to the pattern p t shown to the ...

Consider the prototype patterns shown to the lefti are

Consider the prototype patterns shown to the left. i. Are these patterns orthogonal? ii. Design an autoassociator for these patterns. Use the Hebb rule. iii. What response does the network give to the test input pattern, ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen