Ask Question, Ask an Expert

+61-413 786 465

info@mywordsolution.com

Ask Electrical & Electronics Expert

The problem with a battery charger (say, for portable devices) is that it continues to draw power even after the battery is fully charged thereby wasting electricity. In addition, this results in undermining the lifetime of the battery. Design a battery charger, which could outperform the existing charger by charging a battery to its full potential and then alert the user that it is completely charged and importantly, turn-off the power to the device. This would help in improving the energy efficiency. The functionality of the charger must be demonstrated through experiments. Specifications for a target application (say, a mobile phone or digital camera) can be chosen based on the availability of components/devices and design cost involved.

SOLUTION has to be 50 pages excluding appendix if required.

excluding appendices which could contain supplementary drawings, program listings etc. It is your responsibility to organise and if necessary pay for the typing of the Report. The School does leave scope for individual report presentation style.   Typically however, the following structure is preferred:

  • suitable front page,
  • one paragraph summary (abstract) on a page of its own,
  • contents page,
  • introduction,
  • problem analysis,
  • problem solution,
  • problem implementation,
  • results,
  • discussion of results,
  • conclusion,
  • future work,
  • references,
  • project timetable (e.g. Gantt chart),
  • appendices (if required)

General rules which should be followed:

1. The typescript should not extend into the binding of the folder and should use 1 line spacing and be left justified. Program listings and tables should be single spaced.

2. Font size 12 should be used and all pages should be consecutively numbered.

3. Any table, graph, sketch or photograph which for some good reason has to be presented at right angles to the binding, should be arranged with its top towards the binding.

4. Referencing should adhere to the Harvard standard. You can find a guide to Harvard referencing under the "Study Skills Support" section on the Portal. You can also seek guidance from your supervisor.

NB. You must include a number of appropriate references in your report. Whilst it is recognised that the WWW is a fantastic source of material this must be used wisely. It is acceptable to use it to access attributable material, such as journal or conference papers,  properly authored e-books, manufacturer?s data sheets etc, provided you properly reference these.  That is you reference the paper, e-book, data sheet etc, NOT the web address. Un-attributable Web material, such as Wikipedia, will not be counted.

Remember, you must, for completeness, properly reference all your source material and when evaluating your report only references to certified sources will be given due weighting.

TIP: If you are using Word 2007 or later, use the excellent reference manager to input your reference and insert them into your  document.

Selecting the "APA" style will automatically set the reference format to a style comparable with the Harvard system.

5. The use of colour is left to the student, but should be used with discretion. Note that all copies of the report should be the same.

6. Be sure to use the UK English version of the spellchecker, NOT the US „American? English.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M9525442

Have any Question?


Related Questions in Electrical & Electronics

Question 1 a pnp transistor withnbspbeta 60 is connected

Question 1. A pnp transistor with β = 60 is connected in a common-base configuration as shown in figure P5.8 (a) The emitter is driven by a constant-current source with I E = 0.75 mA. Determine I B , I C , α, and V C . ( ...

Research report1 read 3 to 4 journal articles about digital

Research report 1. Read 3 to 4 journal articles about digital control or industrial control, eg. one particular application, implementation aspect such as selection of sampling time, hardware etc. No text book example is ...

Assignment -problem 1 -a consider the simplified dc system

Assignment - Problem 1 - a) Consider the simplified dc system shown in Fig. 1. Only one converter is modeled, with the remote end represented by a dc source. The ac system is rated at 345 kV, with the converter transform ...

Nanotechnology engineering - resonance circuits questions

Nanotechnology Engineering - Resonance Circuits Questions - Q1) A series RLC network has R = 2KΩ, L = 40mH and C = 1μF. Calculate the impedance at resonance and at one-fourth, one-half, twice, and four times the resonant ...

Electrical engineering questions -q1 two ideal voltage

Electrical Engineering Questions - Q1. Two ideal voltage sources designated as machines 1 and 2 are connected, as shown in the figure below. Given E 1 = 65∠0 o V, E 2 = 65∠30 o V, Z = 3Ω. Determine if Machine 1 is genera ...

Questions -problem 1 - given the sinuosidal voltage vt 50

Questions - Problem 1 - Given the sinuosidal voltage v(t) = 50 cos(30t+10 o ) V, find: (a) the amplitude V m (b) the period T, (c) the frequency f and (d) v(t) at t = 10 ms. Problem 2 - A current source in a linear circu ...

1 a name the three major groups of contamination and

1. (a) Name the three major groups of contamination and briefly describe their physical characteristics. (b) Where do the above contamination types come from? Give one example of each. 2. Name two processes metrics which ...

1 goalin this project you will solve a non-trivial design

1 Goal In this project you will solve a non-trivial design problem explicitly using the divide-and-conquer (D&C) approach. The main reason for using the D&C approach is the ease of the design process and the streamlined ...

Case studythis assignment consists of a written report of

CASE STUDY This assignment consists of a written report of approximately 1000 words and any diagrams in which you are asked to critically compare different process methods used to achieve the same result and show an awar ...

Question 1for the ce amplifier in figure 1 given the

Question 1 For the CE amplifier in Figure (1), given the following component parameters: Parameter Value β DC , β AC 150 V BE 0 . 7 V V CC 12 V R C 820 ? R E 1 100 ? R E 2 220 ? R 1 20 k? R 2 5 . 2 k? R L 100 k? C 1 , C ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As