Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1: A regular hexagon of 35 mm side is resting on an edge in HP and the surface of the hexagon is inclined at 45° to HP and perpendicular to VP. Draw its projections.

problem 2: A hexagonal pyramid of base edge 25 mm and height 70 mm is resting on one of the base edge on HP and the base makes an angle of 45° to HP, with its axis parallel to VP. Draw its projections.

problem 3: The orthographic views of a machine bracket are shown in figure below. Draw isometric view from such views and dimension them.

2193_orthographic views.jpg

problem 4: Draw the given views of the block as shown in figure below by using either 1st Angle Projection or 3rd Angle Projections:

a) Top-View.
b) Front-View.
c) Side-view.

2134_first and third angle projection.jpg

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M92689

Have any Question? 


Related Questions in Mechanical Engineering

1 a differential manometer is used to measure the pressure

1. A differential manometer is used to measure the pressure change caused by a flow constriction in a piping system as shown. Determine the pressure difference between points A and B in psi. Which section has the higher ...

A transformer winding was designed to be fed by an ac

A transformer winding was designed to be fed by an ac voltage of 110 V and to produce an effective current of 10.5 A. By mistake, the transformer was fed from this same voltage but rectified in a full wave converter. Con ...

1 for the pipe-flow-reducing section d1nbsp 8 cm d2nbsp 5

1. For the pipe-flow-reducing section D 1  = 8 cm, D 2  = 5 cm, and p 2  = 1 atm. If v 1  = 5 m/s and the manometer reading is h =58 cm, estimate the total force resisted by the flange bolts. 2. An open tank car as shown ...

As can often be seen in a kitchen sink when the faucet is

As can often be seen in a kitchen sink when the faucet is running, a high-speed channel flow (v 1 , h 1 ) may ''jump'' to a low-speed, low-energy condition (v 2 , h 2 ). The pressure at sections 1 and 2 is approximately ...

The stepped shaft rotates at 120 rpm and has a 20 kw input

The stepped shaft rotates at 120 rpm and has a 20 kW input at A. 16 kW is taken off to operate machinery at B, and the remaining 4 kW is used at C. The shaft is stainless steel with yield strength in shear of 300 MPa. a. ...

The velocity profile in the annular control volume of

The velocity profile in the annular control volume of Example is approximately linear, varying from a velocity of zero at the outer boundary to a value of ωd/2 at the inner boundary. Develop an expression for the fluid v ...

1 air at 70degf flows into a 10-ft3nbspreservoir at a

1. Air at 70°F, Flows into a 10-ft 3  reservoir at a velocity of 110 fps. If the reservoir pressure is 14 psig and the reservoir temperature 70°F, find the rate of temperature increase in the reservoir. Assume the incomi ...

Projectdesign a tube bank that will increase the

Project Design a tube bank that will increase the temperature of a 1200 CFM flow of air from 35°F to 100°F. Assume a constant pressure of 1atm. Each tube will have a diameter of 0.5in and a length of 24in. The tube confi ...

1 an automobile is driving into a 45-mph headwind at 40 mph

1. An automobile is driving into a 45-mph headwind at 40 mph. If the barometer reads 29 in. Hg and the temperature is 40°F, what is the pressure at a point on the auto where the wind velocity is 120 fps with respect to t ...

1 sketch the deformation of a fluid element for the

1. Sketch the deformation of a fluid element for the following cases: 2. For a two-dimensional, incompressible flow with velocity v x  = v x (y), sketch a three-dimensional fluid element and illustrate the magnitude, dir ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro