Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

Assignment Title: Speed control of DC motor using PID (proportional integral derivative) control.

The objective of the project is to protect damage of the DC motors. If the motor is not working it will be shown with red light, if working normally then green and if working at a slow speed then it will glow yellow light. The block diagram of the circuitry comprises of the given components:

1926_speed control of DC motor.jpg

Design Steps:

A) Firstly Design the circuit for the assignment
B) Make the layout and draw it on PCB.
C) Design the programming for the assignment.
D) Perform soldering and complete the circuit.

Deliverables:

At the time of submission you have to submit 2 hard copies (spiral bound printed on both sides of paper) comprising soft copy of your documentation.

Documents: Coursework Report

You are advised to limit the number of pages of the report to forty (40) pages. The font size used in the report must be 12pt and Times New Roman. The report must be typed and clearly printed. As part of the assessment, you must submit the project report in printed and softcopy form, which should have the following format:

Cover Page:

All reports must be prepared with a front cover. A protective transparent plastic sheet can be placed in front of the report to protect the front cover. The front cover should be presented with the following details:

A) Module.
B) Coursework Title.
C) Intake.
D) Student name and id.
E) Date Assigned (the date the report was handed out).
F) Date Completed (the date the report is due to be handed in).

Contents:

A) Objective, working principle and detailed theory.               
B) Circuit Designand implementation.
C) Programming.
D) Result and Conclusion.         
E) Formatting of report. 
F) References.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M91011

Have any Question? 


Related Questions in Electrical & Electronics

1 what is a boundary condition how do boundary conditions

1. What is a boundary condition? How do boundary conditions arise and how are they derived? 2. Summarize the boundary conditions for the general case of a boundary between two arbitrary media, indicating correspondingly ...

In natural-convection problems the variation of density due

In natural-convection problems, the variation of density due to the temperature difference ?T creates an important buoyancy term in the momentum equation. If a warm gas at T H moves through a gas at temperature T 0 and i ...

Repeat problem with the elastic constants of the plastic

Repeat Problem with the elastic constants of the plastic defined as E = 10 GPa and ν = 0.485. Problem:- A rectangular plastic specimen of size 100 X 100 X 10 mm 3  is placed in a rectangular metal cavity. The dimensions ...

In a kademlia network with m 4 we have five active nodes

In a Kademlia network with m = 4, we have five active nodes: N2, N3, N7, N10, and N12. Find the routing table for each active node (with only one column).

Question 1a 1000-pf capacitor a 1-mh inductor and a current

Question 1: A 1000-pF capacitor, a 1-mH inductor, and a current source of 2 cos 10 6 t mA are in series. The capacitor voltage is zero at t = 0. Find the energy stored (a) in the inductor at t = 0; (b) in the capacitor a ...

A discuss asymptotic and bibo stabilities for the systems

a. Discuss asymptotic and BIBO stabilities for the systems described by the following transfer functions assuming that the systems are controllable and observable: b. Repeat part (a) for systems described by the followin ...

A 9 kva 208 v l-l 3-phase y connected stator synchronous

A 9 kVA, 208 V (L-L), 3-phase Y connected stator, synchronous generator has a stator resistance of 0.1 ohm per phase, and a synchronous resistance of 5.6 ohm per phase. The generator is driven by a diesel engine, and is ...

1 for the force field f x2ay find the approximate value of

1. For the force field F = x 2 ay, find the approximate value of the line integral of F from the origin to the point (1, 3, 0) along a straight line path by dividing the path into ten equal segments. 2. For the force fie ...

In the system shown in figure 755 steady-state conditions

In the system shown in Figure 7.55, steady-state conditions are established with the switch S closed.At t = 0, he switch is opened. (a) Sketch the voltage and current along the system for t = 0-. (b) Find the total energ ...

1 briefly outline the procedure involved in the successive

1. Briefly outline the procedure involved in the successive solution of Maxwell's equations. 2. How does the technique of successive solution of Maxwell's equations reveal the interaction between the electric and magneti ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen