Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

The figure shown below is an extract from an industrial control panel wiring diagram.

1158_industrial control panel.jpg

Q1. Convert the figure into the PLC format.

Q2. Recognize all the inputs and outputs by the use of input/output designation charts.

Q3. With respect to the operation of circuit:

a) Describe the purpose of rung 1.

b) Describe fully the condition of the circuit elements when indicator IND2 is illuminated.

c) If indicator IND3 is on, then describe what will happen if P3 is operated.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M910092

Have any Question? 


Related Questions in Electrical & Electronics

1 how do you find the approximate value of the surface

1. How do you find the approximate value of the surface integral over a given surface? 2. How do you find the exact value of the surface integral? 3. Provide physical interpretations for the closed surface integrals of a ...

1 state and briefly discuss the basic definition of the

1. State and briefly discuss the basic definition of the curl of a vector. 2. What is a curl meter? How does it help visualize the behavior of the curl of a vector field? 3. Provide two examples of physical phenomena in ...

The rate at which metallic ions are electroplated from a

The rate at which metallic ions are electroplated from a dilute electrolytic solution onto a rotating disk electrode is usually governed by the mass diffusion rate of ions to the disk. This process is believed to be cont ...

1 the tank is accelerated upward at a uniform rate does the

1. The tank is accelerated upward at a uniform rate. Does the manometer level go up or down? 2. Glass viewing windows are to be installed in an aquarium. Each window is to be 0.6 m in diameter and to be centered 2 m belo ...

For each of the following baseband signals i mt cos 1000t

For each of the following baseband signals (i) m(t) = cos 1000t, (ii) m(t) = 2cos 1000t + cos 2000t, and (iii) m(t) = cos 1000t cos 3000t: a. Sketch the spectrum of m(t). b. Sketch the spectrum of the DSB-SC signal m(t) ...

Determine the nyquist sampling rate and the nyquist

Determine the Nyquist sampling rate and the Nyquist sampling interval for the signals a. sinc 2 (100πt) b. 0.01 sinc 2 (100πt) c. sinc(100πt) + 3 sinc 2 (60πt) d. sinc(50πt) sinc (100πt)

Assignment questiondesign automatic fan speed controller

Assignment Question Design automatic fan speed controller based on the temperature variation in room using a microcontroller. Abstract: The electronic Circuit used to control the speed of fan based on temperature variati ...

1 what is the particular advantageous characteristic

1. What is the particular advantageous characteristic associated with the unit vectors in the Cartesian coordinate system? 2. How do you find a vector perpendicular to a plane? 3. How do you find the perpendicular distan ...

A number equal to the sum of its coordinates is assigned to

A number equal to the sum of its coordinates is assigned to each point in a rectangular room having three of its contiguous edges as the coordinate axes. Draw a sketch of the constant-magnitude surfaces for the number fi ...

1 a rectangular block of concrete 3 ft times 3ft times 6 in

1. A rectangular block of concrete 3 ft × 3ft × 6 in. has its 6- in. side half buried at the bottom of a lake 23 ft deep. What force is required to lift the block free of the bottom? What force is required to maintain th ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro