Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

Power System Assignment:

The assessment for this course is to design a substation and the related protection system. The transformer is an existing 33 kV to 11 kV 5 MVA transformers, 3 phase/3 phase Transformer. The selection of transformer connection method, transformer protection and Cooling method is left up to the student. The selection of overhead or underground line feed, protection system, earthling, metering, insulators, security (physical) and related switchgear, and so on is left up to the student. A line flow diagram of the proposed substation Layout is expected as is the consideration of external events like lightning protection and so on.

Each student is expected to work alone and to produce a short, typed Engineering Report (Maximum 12 pages comprising cover page and appendices, summary, references, table of contents and so on). Detailing the design and justifying each decision.

Specific information which will be needed is as shown below:

A) Type of line – that is, type of poles, insulators, type of conductor and so on.
B) Ratings of the Transformer 33/11 kV (Z% = 20%).
C) Outgoing cable.
D) MVA Rating of the 11 kV breaker and fault current.
E) Protection requirements.
F) Earthing.
G) Safety needs.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M92071

Have any Question? 


Related Questions in Electrical & Electronics

1 what is the particular advantageous characteristic

1. What is the particular advantageous characteristic associated with the unit vectors in the Cartesian coordinate system? 2. How do you find a vector perpendicular to a plane? 3. How do you find the perpendicular distan ...

Election polls oversight a reflection on forecast accuracy

Election Polls Oversight: A reflection on Forecast Accuracy and Bias The media, locally and internationally, has been labeling this Election results as Unexpected, based on early predictions that did not realize. We kept ...

The device in the schematic diagram below is a viscosity

The device in the schematic diagram below is a viscosity pump. It consists of a rotating drum inside of a stationary case. The case and the drum are concentric. Fluid enters at A, flows through the annulus between the ca ...

Question 1 design a suitable double -layer lap winding for

Question 1) Design a suitable double -layer lap winding for a 6-pole dc armature with 18 slots and two coil sides per slot. Give values of front-pitch, brack-pitch and commutator pitch. Draw the developed diagram and sho ...

1 discuss the solutions for the transmission-line equations

1. Discuss the solutions for the transmission-line equations in frequency domain. 2. Discuss the propagation constant and characteristic impedance associated with wave propagation on transmission lines. 3. What is the bo ...

1 in which situation a unicast session or a multicast

1. In which situation, a unicast session or a multicast session, can feedback received from an RTCP packet about the session be handled more easily by the sender? 2. Can the combination of RTP/RTCP and SIP operate in a w ...

Compute and plot the solution of the difference equation yn

Compute and plot the solution of the difference equation y[n] þ y[n 1] = 2x[n] þ x[n 1], where x[n] = 0.8n u[n] assuming zero initial conditions. Moreover, verify your answer (a) by examining if the derived solution sati ...

1 two point charges each of mass m and charge q are

1. Two point charges each of mass m and charge q are suspended by strings of length l from a common point. Find the value of q for which the angle made by the strings at the common point is 90°. 2. Point charges Q and ar ...

A periodic signal xt is expressed by the following fourier

A periodic signal x(t) is expressed by the following Fourier series: a. Sketch the amplitude and phase spectra for the trigonometric series. b. By inspection of spectra in part (a), sketch the exponential Fourier series ...

1 why is it necessary to have the displacement current term

1. Why is it necessary to have the displacement current term on the right side of Ampere's circuital law? 2.28. When can you say that the current in a wire enclosed by a closed path is uniquely defined? Give two examples ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro