Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem: The curve in figure below shows the response of the bare thermocouple that has been subjected to the step change in temperature from 50°C to 10°C. Supposing that the bare thermocouple behaves as a single transfer lag system, find out the mathematical relationship between the temperature (T) and time (t).

1240_bare thermocouple.jpg

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M910054

Have any Question? 


Related Questions in Mechanical Engineering

Use eqn 135 to find expressions for the rate of change of

Use eqn 1.35 to find expressions for the rate of change of the expectation values of position and momentum of a harmonic oscillator; solve the pair of differential equations, and show that the expectation values change i ...

Experiment title heat engine experimentacademic in charge

Experiment title: Heat Engine Experiment Academic in charge of experiment: Experiment duration: The standard scheduled time for this experiment is 90 minutes for 3 groups (A, B, C) of 6 students. Each group undertakes ex ...

A prototype bolt shaft assume a uniform cylinder that is to

A prototype bolt shaft (assume a uniform cylinder) that is to be loaded in tension is made of a stainless steel with a yield strength of 450 MPa and has a safety factor of 3 with respect to yielding for the maximum allow ...

List three ways to control preload directly what are the

List three ways to control preload directly ? What are the advantages of a bonded ultrasonic transducer? What is sometimes cited as a disadvantage? Can torque be used to tighten a 6 in. diameter bolt? If not, why not? Na ...

Consider the torsion of a thin-walled tube determine an

Consider the torsion of a thin-walled tube. Determine an approximate expression for the torque if the shear stress must be less than a given working stress τw. Express this result in terms of the tube's mean radius R and ...

1 for the pipe-flow-reducing section d1nbsp 8 cm d2nbsp 5

1. For the pipe-flow-reducing section D 1  = 8 cm, D 2  = 5 cm, and p 2  = 1 atm. If v 1  = 5 m/s and the manometer reading is h =58 cm, estimate the total force resisted by the flange bolts. 2. An open tank car as shown ...

Blood glucose concentration is regulated primarily by the

Blood glucose concentration is regulated primarily by the controlled release of insulin in the pancreas. However, patients with Type I diabetes mellitus are incapable of producing insulin and therefore require shots of i ...

Optional extra credit problemyou have been given a map

OPTIONAL EXTRA CREDIT PROBLEM You have been given a map which references a monument having coordinates North 2403306.986, East 5873350.973, expressed in US Survey Feet. A statement on the map states that the area mapped ...

A nut having an effective length of 2 in and a 12-16 un

A nut having an effective length of 2 in. and a 1/2-16 UN thread is snug tightened and then turned 308. How much preload will that create in the bolt? Is that an acceptable preload? Describe the typical torque-turn tight ...

Draw the moment diagram for the elbow-biceps-forearm-hand

Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment if the total weight w of the forearm and hand are included and are assumed to act at the mid ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen