+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1)(i) prepare down the merits and demerits of nuclear power plant.

(ii) State self and mutually induced emfs?

(iii) Draw and describe phasor diagram for the R-L series circuit.

(iv) Describe hysteresis loss.

(v) What is constant current source and sketch characteristics of an ideal current source.

(vi) A resistor of 100W is connected in series with a 56mF capacitor to a supply at 230 V, 50 Hz. Determine the impedance, the current, the phase angle, the pf and the voltage across the resistor and the capacitor.

(vii) What do you understand by form factor and peak factor ?

problem 2) Determine the impedance, current and the power factor of the following series circuits and sketch the corresponding phasor diagram.

(i) R and L

(ii) R and C

In each case the applied voltage is 200 volt, the frequency is 50 Hz, R = 10 ohm, L = 50 mH; C =100μF.

problem 3)(a) What are the different precautions to be observed for obtaining longer life and batter efficiency of lead acid battery?

(b) State flux, mmf, reluctance and permeability in magnetic circuits.

problem 4) Compare electric and magnetic circuits. What do you understand by power factor ? What is its importance?

problem 5) Describe hydro power plant with the help of schematic diagram.

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M98124

Have any Question?

## Related Questions in Mechanical Engineering

### Water in an open cylindrical tank 15 ft in diameter

Water in an open cylindrical tank 15 ft in diameter discharges into the atmosphere through a nozzle 2 in. in diameter. Neglecting friction and the unsteadiness of the flow, find the time required for the water in the tan ...

### Sea water rho 1025 kgm3 flows through a pump at 021 m3s

Sea water, ρ = 1025 kg/m 3 , flows through a pump at 0:21 m 3 /s. The pump inlet is 0.25 m in diameter. At the inlet the pressure is -0.15 m of mercury. The pump outlet, 0.152 m in diameter, is 1.8 m above the inlet. The ...

### Name at least three reasons why some bolts fail

Name at least three reasons why some bolts fail mechanically? What is the most common cause of bolted joint misbehavior or failure? Name at least two problems that can be caused by overtightening the bolts? What do we me ...

### A gas sample is known to be a mixture of ethane and butane

A gas sample is known to be a mixture of ethane and butane. A bulb having a 230.0 cm 3 capacity is filled with the gas to a pressure of 97.5 X 10 3 Pa at 23.1°C. If the mass of the gas in the bulb is 0.3554 g, what is th ...

### Question 1 -1 plot the singular stress components sigmaxx

Question 1 - 1) Plot the singular stress components, σ xx , σ yy and τ xy for a cracked body under Mode I, Mode II and Mode III loading with a stress intensity factor K i = 10 MPa·m 1/2 (i = I, II and III). Plot the stre ...

### The jaws of the bolt cutter shown are connected by two

The jaws of the bolt cutter shown are connected by two links AB. The cross-sectional area of each link is 750 mm 2 . (a) What average normal stress is induced in each link by the 90 N forces exerted on the handles? (b) T ...

### Project -this project is individual work write a computer

Project - This project is individual work. Write a computer program using Matlab to read the engineering constants E 1 , E 2 , v 12 , and G 12 then computes and prints the Reduced Compliances Matrix [S], the Reduced Stif ...

### As an approximate rule a particular vibrational mode in a

As an approximate rule, a particular vibrational mode in a molecule will contribute to the equipartition principle energy at temperatures where 3 2 kBT Ú ve for that mode. In the following table are listed all the vibrat ...

### Select a topic on the discussion board discussion section

Select a topic on the discussion board (DISCUSSION section of blackboard) There are four categories of topics; organizations, testing methods, elements and specialty components. Each has something to do with industrial m ...

### Problem -a consider a one-component system consisting of

Problem - a. Consider a one-component system consisting of spherical bubbles of vapor inside a liquid, which is commonly observed as a liquid begins to boil. This is similar to the case considered in class in which liqui ...

• 4,153,160 Questions Asked
• 13,132 Experts
• 2,558,936 Questions Answered

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

### Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen