Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1)a) State degree of freedom of a vibratory system.

b) Name the three elementary parts of a vibrating system?

c) What is a semi definite system?

d) What are the common types of damping?

e) What do you undrstand by beat phenomenon?

f) What is vibration isolation?

g) Mention two practical exs of critical damping.

h) What is principal co-ordinates?

i) prepare down the name of seismic instruments.

j) What are influence co-efficients?

In a spring mass system, the mass of 10 kg makes 40 oscillations in 20 seconds without damper. With damper, the amplitude decreases to 0.20 of the original; value after 5 oscillations.

Find out: (a) Stiffness of the spring.

(b) Logarithmic decrement.

(c) Damping factor.

(d) Damping co-efficient.

problem 4) Sketch a neat sketch of centrifugal pendulum absorber and describe its working.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98188

Have any Question? 


Related Questions in Mechanical Engineering

1 a square gate 4 m by 4 m is located on the 45deg face of

1. A square gate, 4 m by 4 m, is located on the 45° face of a dam. The top edge of the gate is 8 m below the water surface. Determine the resultant force of the water on the gate, and the point through which it acts. 2. ...

For a deck supports of length 325 m are proposed to be

For a deck, supports of length 3.25 m are proposed to be built from aluminum with a Young's modulus of 72 GPa and a yield stress of 480 MPa. A cylindrical design is proposed with outer diameter d = 100 mm and wall thickn ...

1 in more than one paragraph but less than a page discuss

1. In more than one paragraph but less than a page, discuss some of the failure modes experienced in the collapse of the World Trade Center and how they might have been prevented. 2. A truss ABC supports a load W at join ...

Calculate the size h of the two welds required to attach a

calculate the size h of the two welds required to attach a plate to a frame as shown in figure. if the plate supports an inclined force P=50kn. use a factor safety of 3 and yield shear stress of 350 mpa for the weld mate ...

What primary factors determine the number of load cycles

What primary factors determine the number of load cycles required to break a bolt subject to fatigue loading? Describe the appearance of the break surface of a bolt which has failed in fatigue ? Where on a bolt are you m ...

An electrical motor is used to operate a carnot

An electrical motor is used to operate a Carnot refrigerator with an interior temperature of 0.00°C. Liquid water at 0.00°C is placed into the refrigerator and transformed to ice at 0.00°C. If the room temperature is 300 ...

1 write down the equations for the reverse active mode by

1. Write down the equations for the reverse active mode by inspection without doing any algebra. 2. Are there any currents flowing in the cutoff mode? What is their magnitude if there are? 3. Obtain the saturation voltag ...

Compute a reasonable torque for an as-received unlubricated

Compute a reasonable torque for an as-received, unlubricated 1/2 -32  = 4 SAE J429 GR 5 bolt in a nonsafety-related normal application ?  Compare your torque to that suggested in Appendix E ?  When estimating bolt tensio ...

If you were using a full length centerline gage rod to

If you were using a full length, centerline, gage rod to measure DL, how much change would you expect to see at 2508F?  What DL from ‘‘before tightening'' would you expect to see at 2508F if you were using ultrasonics to ...

Calculate the pressure in bar that would be equivalent to

Calculate the pressure in bar that would be equivalent to the attractive force between the Na + and Cl - ions in a salt crystal, at a separation of 2.81 Å and approximating the area over which the force works to be 4.00A ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro