Ask Question, Ask an Expert

+61-413 786 465

info@mywordsolution.com

Ask Mechanical Engineering Expert

Standard Operating

Background Information: You have just been promoted to the rank of lieutenant (or bureau manager if serving in the private sector) and have been appointed to the Fire Prevention Bureau/Office as the new supervisor/leader. Your predecessor held the position for many years and had his or her own way of keeping, storing, and maintaining fire prevention records.

You soon discover that records are in total disarray and very few records are properly stored, nor have the volumes of the records been properly maintained and protected from the environment in which they were stored. You have a bureau crew of four other employees who have had little involvement in the handling of records and you plan to change that.

Task: The purpose of this essay is for you to apply the concepts and information you have learned in this unit about the position of a Fire Prevention Officer/Manager. This assignment provides you with the opportunity to use your skills, expertise, and experience to enrich your response when compiling data that will be used for risk reduction within the community. You will compose a standard operating guideline (SOG) that should address the following components:

provide an introduction into what this SOP is designed to accomplish along with the Mission Statement for this Division.

proper recording of bureau/office inspections, incidents, testing, re-testing, and re-inspections;

proper storage of all records gathered by the bureau/office; and

proper maintenance of all stored records for the required amount of time as set-forth by local, state, and/or federal rules and regulations.

You should be clear, concise, and ensure that the SOG addresses each of the three bulleted components given above. The final SOG packet must contain a minimum of one full page for each of the three components listed above; no component can have more than two full pages of text.

Keep in mind that your SOG narratives must be straight-to-the-point. Avoid long rambling narrations as these tend to distract attention and often lead to confusion and misunderstanding of purpose and functionality.

Remember, you are the head of this newly formed bureau and you want to impress your leadership with your knowledge, academic ability, and occupational experience. Be innovative and creative; however, be sure to utilize a variety of sources that must include your textbook. Your final paper will become your SOG to be used and referred to in your day-to-day operations.

To better help you in the formatting and completion of this assignment, please click here to see a template which can be used to help you in composing your SOG.

Your sources must be cited, and referenced in APA format.

Attachment:- unitvii_csu_sogexample.rar

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M92216743
  • Price:- $40

Priced at Now at $40, Verified Solution

Have any Question?


Related Questions in Mechanical Engineering

Problem on shaft -assuming no frictional losses a torque of

Problem on Shaft - Assuming no frictional losses, a torque of T = 750lb·in is applied through the shaft of gear F in order to drive the roller chain at point B at a constant speed. The chain sprocket has a pitch diameter ...

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Life cycle assessmentfor your chosen service eg white

LIFE CYCLE ASSESSMENT For your chosen service (e.g. white board markers), identify two alternatives of getting the service (e.g. brand A, brand B). Choose the most environmentally friendly option by conducting life cycle ...

Assignment -q1 explain the difference between the

Assignment - Q1. Explain the difference between the metacentric height of a ship during 'Partially Afloat condition and 'Free Floating' condition; aid a sketch to support your answer. Q2. With the aid of sketches, explai ...

Fluid mechanics assignment - viscous flow in pipesq1 as

Fluid Mechanics Assignment - Viscous Flow in Pipes Q1. As shown in the figure below, water "bubbles up" 3 in. above the exit of the vertical pipe attached to three horizontal pipe segments. The total length of the 0.75-i ...

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

Problem - A long pipe (OD = 141.3 mm, ID =131.8 mm, k p = 20 W/m.K) supplies hot pressurized liquid water at 400 K to a heater in a factory. The pipe has an insulation thickness of 100 mm. A new efficient heater replaces ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

Mechanical engineering assignment task - solve the given

Mechanical Engineering Assignment Task - Solve the given problem. Task 1 - A spring with a one-turn loop of 40mm mean radius is formed from a round section of wire having 5 mm diameter. The straight tangential legs of th ...

Assignment - machine learning for signal processingproblem

Assignment - Machine Learning for Signal Processing Problem 1: Instantaneous Source Separation 1. As you might have noticed from my long hair, I've got a rock spirit. However, for this homework I dabbled to compose a pie ...

Alocate ten minutes for the presentationuse audio visual

Allocate ten minutes for the presentation Use audio / visual / technological supports / aids where appropriate Use a minimum of 3 properly referenced articles. THEMES PRESENTATION TOPIC MEMORY Discuss the three learning ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As