Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) Specify two metals having re-crystallisation temperature below theroom temperature.

2) Specify the difference between the blanking and the piercing.

3) Specify the use of the carburising flame?

4) State the various welding defects possible.

5) describe the term gating system?

6) Specify the difference between the hot chamber die casting and cold chamber die casting processes?

7) State two electrolytes that are used in electrochemical machining.

8) Specify the purpose of the dielectric fluid EDM.

9) Briefly describe the meaning of CAD.

10) prepare down the difference between the NC and the CNC.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M913554

Have any Question? 


Related Questions in Mechanical Engineering

Suppose that you measured the product pv of 1 mol of a

Suppose that you measured the product PV of 1 mol of a dilute gas and found tha PV = 24.35 L atm at 0.00°C and 33.54 L atm at 100.°C. Assume that the ideal gas law is valid, with T = t(°C) + a and that the values of R an ...

1 in more than one paragraph but less than a page discuss

1. In more than one paragraph but less than a page, discuss some of the failure modes experienced in the collapse of the World Trade Center and how they might have been prevented. 2. A truss ABC supports a load W at join ...

The case study kahiki-foods-case-study critique it and do a

The case study kahiki-foods-case-study CRITIQUE it and do a 10-12 pages report about it their are notes and a presentation done about it that you can use in doing the paper Also their is an example of a different case wh ...

1 concrete rocks and bone are strong in compression and are

1. Concrete, rocks, and bone are strong in compression and are usually designed for compressive loading. To test their strength in compression, what sort of test specimen would be useful? 2. Suppose that a downward force ...

Define prying action sketch an alternative joint diagram

Define prying action? Sketch an alternative joint diagram showing the effects of prying action Name at least two things the joint designer can do to reduce prying action? This and the following three questions are all in ...

The ground state 1s1 h atom has two hyperfine states f 0

The ground state 1s1 H atom has two hyperfine states, F = 0 and F = 1, which correspond to different relative orientations of the nuclear spin and electron spin. The transition between these two states has a wavelength o ...

Need a 400 to 500 minimum word essay on 2 articles no

Need a 400 to 500 minimum word essay on 2 articles (No internet, just based on the articles) - You will need to do a compare and contrast essay where you compare an Old HVAC system with a New system and also old refriger ...

A laminated plastic beam with a square cross section is

A laminated plastic beam with a square cross section is built up by gluing together three strips, each 10 mm × 30 mm in cross section. It must carry a load P at its midpoint. a. The beam has a total weight W and a length ...

List three ways to control preload directly what are the

List three ways to control preload directly ? What are the advantages of a bonded ultrasonic transducer? What is sometimes cited as a disadvantage? Can torque be used to tighten a 6 in. diameter bolt? If not, why not? Na ...

A nut having an effective length of 2 in and a 12-16 un

A nut having an effective length of 2 in. and a 1/2-16 UN thread is snug tightened and then turned 308. How much preload will that create in the bolt? Is that an acceptable preload? Describe the typical torque-turn tight ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro