Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) Describe the memory organization of 8051.

2) Specify the Timers in 8051 and describe them in detail.

3) prepare down the different classification of the Instruction set of 8051 and describe them with the help of exs.

4)  describe the assembly language program for carrying out the BCD addition.

5) describe about the PIC 16F877 architecture in detail with the help of neat diagram.

6) Specify the different addressing modes of the PIC 16F877 and describe them with the support of exs.

7) Describe about the Embedded networking in detail.

8) prepare down a brief notes on the I2C and RS485.

9) Compare and contrast Desktop OS and RTOS.

10) Specify the need for scheduling and describe its types?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M913311

Have any Question? 


Related Questions in Electrical & Electronics

1 what is the laplacian of a scalar what is its expansion

1. What is the Laplacian of a scalar? What is its expansion in Cartesian coordinates? 2. State Poisson's equation. 3. Outline the solution of Poisson's equation for the potential in a region of known charge density varyi ...

Determine the pressure gradient at the stagnation point of

Determine the pressure gradient at the stagnation point of Problem. Problem For the velocity potentials given below, find the stream function and sketch the streamlines

1 discuss the application of the directional receiving

1. Discuss the application of the directional receiving properties of a loop antenna in the location of the source of a radio signal. 2. How is the effective area of a receiving antenna defined? 3. Outline the derivation ...

Consider the complementary-bjt class b output stage and

Consider the complementary-BJT class B output stage and neglect the effects of finite VBE and VCEsat. For ±10-V power supplies and an 8 ohm load resistance, what is the maximum sine-wave output power available? What supp ...

1 if the plate shown is inclined at an angle as shown what

1. If the plate shown is inclined at an angle as shown, what are the forces F x  and F y  necessary to maintain its position? The flow is frictionless. 2. A steady, incompressible, frictionless, two-dimensional jet of fl ...

Write the expression for the vector distance of a point in

Write the expression for the vector distance of a point in a rectangular room from one corner of the room, choosing the three edges meeting at that point as the coordinate axes. Describe the vector distance field associa ...

For the euler beam element shown in the figure derive the

For the Euler beam element shown in the figure, derive the interpolation functions, N I (ξ), stiffness matrix, k, and nodal force vector, f. Assume that the uniformly distributed load is  f (x) = f. Note that the referen ...

Instructions calculate the circuits by filling in all the

Instructions: Calculate the circuits by filling in all the blanks. 1. Et = 24 volts It = ______ amps Rt = ______ ohms 2. Et = 24 volts It = ______ amps Rt = ______ ohms 3. Et = 12 volts It = ______ amps Rt = ______ ohms ...

1 briefly discuss the determination of the fresnel

1. Briefly discuss the determination of the Fresnel reflection and transmission coefficientsv for an obliquely incident wave on a dielectric interface. 2. What is total internal reflection? Discuss the nature of the refl ...

An initially straight beam ab is bent into a circular arc

An initially straight beam AB is bent into a circular arc A'B' as shown in the figure. The deformation is specified as Where g(X 2 ) is a simple function of X 2 . (a) Find the deformation gradient in terms of g(X 2 ). (b ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro