Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

I have a site that a duplex building is to be constructed on it, but the Soil Test conducted revealed soil geology of soft silty clayey sand from 0.0metre level to 8.00metres. Kindly advise what type of foundation solution should be adopted?

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M998596

Have any Question? 


Related Questions in Civil Engineering

Accelerated strength testing of portland - pozzolan cement

Accelerated Strength Testing of Portland - Pozzolan Cement Concretes by the Warm Water Method Background Portland - Pozzolan cement has an important place among the group of blended cements and it is well known that the ...

We would like an lvq network that classifies the following

We would like an LVQ network that classifies the following vectors according to the classes indicated: i. How many neurons are required in each layer of the LVQ network? ii. Define the weights for the first layer. iii. D ...

1 what is the meaning of the term structural i how is it

1. What is the meaning of the term STRUCTURAL I? How is it used? 2. What are the veneer grades? Which veneers are the more similar in appearance and surface qualities? Which veneers are structurally more similar? State t ...

The airflow system in prob 760 is measured with a venturi

The airflow system in Prob. 7.60 is measured with a venturi having like dimensions as the orifice, i.e., the same pipe diameter and throat diameter. Calculate the flow rate in kg/s for the same pressure and temperature m ...

Consider a single-input neuron with a bias we would like

Consider a single-input neuron with a bias. We would like the output to be -1 for inputs less than 3 and +1 for inputs greater than or equal to 3. i. What kind of a transfer function is required? ii. What bias would you ...

The figure shows a schematic of a torsion-bar suspension

The figure shows a schematic of a torsion-bar suspension for an auto mobile (the torsion bar appears in cross section at A). If the three forces and the couple C = 900 lb · ft are equivalent to a upward vertical force R ...

Objectivethe fundamental objectives of this assignment is

OBJECTIVE: The fundamental objectives of this assignment is to demonstrate the student ability to 1. Use the knowledge of different analysis methods learned in lectures to solve the task given in this assessment 2. Use S ...

The homogeneous cylinder of weight w and radius r rests in

The homogeneous cylinder of weight W and radius R rests in a groove of width 2b. Determine the smallest force P required to roll the cylinder out of the groove. Assume that there is enough friction to prevent slipping.

A single-layer neural network is to have six inputs and two

A single-layer neural network is to have six inputs and two outputs. The outputs are to be limited to and continuous over the range 0 to 1. What can you tell about the network architecture? Specifically: i. How many neur ...

Suppose that we have a linear autoassociator that has been

Suppose that we have a linear autoassociator that has been designed for Q orthogonal prototype vectors of length R using the Hebb rule. The vector elements are either 1 or -1. i. Show that the Q prototype patterns are ei ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro