Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

I have a site for a duplex building to be constructed on it, and Soil Test conducted on the site reveals a geology and stratigraphy of soft silty clay to sand from 0.0level to 8.00metres. Kindly advise what type of foundation design or solution should be adopted please?

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M998597

Have any Question? 


Related Questions in Civil Engineering

An n-bit updown counter is a sequential circuit with a

An N-bit up/down counter is a sequential circuit with a clock input and an up/down control input. Wen control is 1, the circuit counts up, modulo 2N, on each rising edge of the clock. In other words, the present-state ou ...

The moment of the force f about the x-axis is 1080 n middot

The moment of the force F about the x-axis is 1080 N · m. Determine the moment of F about the axis AB.

An open-circuit wind tunnel draws in sea-level standard air

An open-circuit wind tunnel draws in sea-level standard air and accelerates it through a contraction into a 1 m-by-1 m test section. A differential pressure transducer mounted in the test section wall measures a pressure ...

Te forces p and q act on the handles of the wrench if p

The forces P and Q act on the handles of the wrench. If P = 32 lb and Q = 36 lb, determine the combined moment of the two forces about the z-axis.

The tongs shown are designed for lifting blocks of ice if

The tongs shown are designed for lifting blocks of ice. If the weight of the ice block is W, find the horizontal force between the tongs and the ice block at C and D.

Literature reviewwhat is waste paper ashis a waste material

LITERATURE REVIEW What is Waste Paper Ash? Is a waste material collected from the Paper Industry How is it generated? Why I want to use it as replacement to cement ? Effect of strength & workability for WPA , FA, SA, WA ...

1 briefly describe what is meant by resawn glulam what

1. Briefly describe what is meant by resawn glulam. What range of sizes is listed in NDS Supplement Tables 1C and 1D for resawn glulam? 2. What is the most common type of lamination end-joint splice used in glulam member ...

The table can be lifted without tilting by applying the

The table can be lifted without tilting by applying the 100-N force at O A y 40 lb 2 ft 90 lb ⋅ft 5 ft 3 ft z x Fig. P2.90 point O, the center of the table. Determine the force-couple system with the force acting at corn ...

Two identical rollerseach of weight 90n are supported by an

Two identical rollers,each of weight 90N are supported by an inclined plane and a vertical wall as shown in fig., determine the reaction at the points of supports A,B,C assuming all the surfaces to be smooth. Also find t ...

Question if y1 and y2 are alternate depths of a rectangular

Question: If y 1 and y 2 are alternate depths of a rectangular channel show that y c  → Criticle depth 2y 1 ²y 2 ²/(y 1 +y 2 ) = Y c 3 and hence the specific energy, E = (y 1 2 + y 1 y 2 +y 2 2 )/(y 1 + y 2 ) No of Pages ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen