Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1)(a) describe the functions of different signals exchanged between a terminal and a modem.

(b) prepare down the algorithm and assembly program to determine factorial of the integer number N using recursive procedure.

problem 2)(a) Draw and describe the 8086 bus activities during prepare machine cycle.

(b) What do you understand by addressing mode? What are the various addressing modes supported by 8086? Describe each with appropriate ex.

problem 3) Describe the interrupt mechanism, types and priority of 8086 microprocessor.

problem 4) Sketch the internal architecture of 8086 microprocessor and describe its each block in with full description.

problem 5) Sketch the pin schematic of DMA controller and describe the series of actions which a DMA controller will carry out after it receives a request from a peripheral device to transfer data from peripheral device to memory.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M99524

Have any Question? 


Related Questions in Electrical & Electronics

1 what is the criterion for a material to be a good

1. What is the criterion for a material to be a good conductor? 2. Give two examples of materials that behave as good conductors for frequencies of up to several gigahertz. 3. What is skin effect? Discuss skin depth, giv ...

Suppose a geologist has collected 15 specimens of a certain

Suppose a geologist has collected 15 specimens of a certain rock, call it R1, and 10 specimens of... Suppose a geologist has collected 15 specimens of a certain rock, call it R1, and 10 specimens of another rock, call it ...

1 state and briefly discuss the basic definition of the

1. State and briefly discuss the basic definition of the curl of a vector. 2. What is a curl meter? How does it help visualize the behavior of the curl of a vector field? 3. Provide two examples of physical phenomena in ...

The performance of a journal bearing around a rotating

The performance of a journal bearing around a rotating shaft is a function of the following variables: Q, the rate of flow lubricating oil to the bearing in volume per unit time; D, the bearing diameter; N, the shaft spe ...

1 what is a boundary condition how do boundary conditions

1. What is a boundary condition? How do boundary conditions arise and how are they derived? 2. Summarize the boundary conditions for the general case of a boundary between two arbitrary media, indicating correspondingly ...

1 if the plate shown is inclined at an angle as shown what

1. If the plate shown is inclined at an angle as shown, what are the forces F x  and F y  necessary to maintain its position? The flow is frictionless. 2. A steady, incompressible, frictionless, two-dimensional jet of fl ...

1 for flow at very low speeds and with large viscosity the

1. For flow at very low speeds and with large viscosity (the so-called creeping flows) such as occur in lubrication, it is possible to delete the inertia terms, Dv/Dt, from the Navier- Stokes equation. For flows at high ...

Figure p77-4a shows a scheme to transmit two signals m1t

Figure P7.7-4a shows a scheme to transmit two signals m1(t) and m2(t) simultaneously on the same channel (without causing spectral interference). Such a scheme, which transmits more than one signal, is known as signal mu ...

1 two point charges each of mass m and charge q are

1. Two point charges each of mass m and charge q are suspended by strings of length l from a common point. Find the value of q for which the angle made by the strings at the common point is 90°. 2. Point charges Q and ar ...

The mass m of drops formed by liquid discharging by gravity

The mass M of drops formed by liquid discharging by gravity from a vertical tube is a function of the tube diameter D, liquid density, surface tension, and the acceleration of gravity. Determine the independent dimension ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro