Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) describe what is main function of the lathe in brief?

2) Describe the cutting tool nomenclature for the single point cutting tool with suitable sketch.

3) describe the tool signature with appropriate ex?

4) List the taper turning method on lathe. describe any one of them.

5) Job which is having length of 100mm is to be turned on the lathe. A length of taper is 60mm with 4 larger diameters of taper 30mm and the smaller diameter 20 mm. Determine half taper angles.

6) prepare differences between the NC and CNC machine?

7) Classify the CNC machine as per the following given condition:

a) According to the control system.

b) According to the system feature.

c) According to the tool positioning system.

3) Describe the constructional attributes of CNC lathe?

4) What is meant by the part program? Describe in detail.

5) describe the benefits and drawbacks of CNC machine?

6) Describe any 5 of G code and M code?

7) Describe the twist drill with suitable sketch.

8) Describe the cutting speed in drilling?

9) describe the deep hole drilling and advantages with the help of neat sketch.

10) describe how machine time is determined for drilling?

11) Describe the operation of drilling machine.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M912065

Have any Question? 


Related Questions in Electrical & Electronics

Assignmentexercise 1 damping ratewe study the response of

Assignment Exercise 1: damping rate We study the response of the circuit of figure 1 to a step e(t). Figure 2 shows the output of the circuit as function of the time. The step signal during all this exercise. 1. Give the ...

Consider the problem of identifying the nonlinear

Consider the problem of identifying the nonlinear discrete-time system in (9.9.4) using a raised-cosine RBF network. Let the number of past inputs be m = 1 and the number of past outputs be n = 1. Suppose the range of va ...

1 compute the radiation resistance per kilometer length of

1. Compute the radiation resistance per kilometer length of a straight power-line wire. Comment on the effectiveness of the power line as a radiator. 2. Find the time-average power required to be radiated by a Hertzian d ...

Give examples of numerical problems in network analysis

Give examples of numerical problems in network analysis with solutions and justification where, (1) Superposition theorem may be more useful than mesh/nodal analysis (2) The use of Thevenin's/Norton's equivalent circuit ...

1 why may researchers not offer potential participants

1. Why may researchers not offer potential participants large incentives (for example, a large amount of money) to participate in research? 2. In general, how much mental or physical risk is permissible in research? 3. D ...

An ltic system impulse response is given by ht ut-ut - 1a

An LTIC system impulse response is given by h(t) = u(t)-u(t - 1). a. Determine the transfer function H(s). Using H(s), determine and plot the magnitude response |H(jω)|. Which type of filter most accurately describes the ...

1 what is the direction of the magnetic field for a uniform

1. What is the direction of the magnetic field for a uniform plane wave having its electric field in the positive z-direction and propagating in the positive x-direction? 2. What is intrinsic impedance? What is its value ...

1 describe the phasor technique of solving a differential

1. Describe the phasor technique of solving a differential equation for the sinusoidal steady-state solution. 2. State Coulomb's law. To what law in mechanics is Coulomb's law analogous? 3. What is the definition of the ...

1 for flow at very low speeds and with large viscosity the

1. For flow at very low speeds and with large viscosity (the so-called creeping flows) such as occur in lubrication, it is possible to delete the inertia terms, Dv/Dt, from the Navier- Stokes equation. For flows at high ...

Discretize the continuous-time system with transfer

Discretize the continuous-time system with transfer function H(s) = (s + 10 )/s with use of the bilinear (Tustin) approximation method. Verify your result by converting the computed discrete-time system to continuous-tim ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro