Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1. describe the functions of different signals exchanged between a terminal and a modem.

2. prepare down the algorithm and assembly program to determine factorial of the integer number N using recursive procedure.

3. Sketch and describe the 8086 bus activities during prepare machine cycle.

4. What do you understand by addressing mode? What are the various addressing modes supported by 8086? Describe each with appropriate ex.

5. Describe the interrupt mechanism, types and priority of 8086 microprocessor.

6. Design the internal architecture of 8086 microprocessor and describe its each block in detail.

7. Design the pin schematic of DMA controller and describe the series of actions that a DMA controller will do after it receives a request from the peripheral device to transfer data from peripheral device to memory.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M99477

Have any Question? 


Related Questions in Electrical & Electronics

1 outline the steps involved in the magnetostatic field

1. Outline the steps involved in the magnetostatic field analysis of a parallel plate structure and the determination of its inductance. 2. Outline the steps involved in the electromagnetostatic field analysis of a paral ...

Objectivesthe objectives of this experiment are1 to

OBJECTIVES: The objectives of this experiment are: 1) To investigate the operation of automatic reset circuits. 2) To understand the difference between a positive edge triggered, negative edge triggered, and a level trig ...

1 how do you find the approximate value of the surface

1. How do you find the approximate value of the surface integral over a given surface? 2. How do you find the exact value of the surface integral? 3. Provide physical interpretations for the closed surface integrals of a ...

1 in one-dimensional dct if n 1 the matrix transformation

1. In one-dimensional DCT, if N = 1, the matrix transformation is changed to simple multiplication. In other words, M = T × p, in which T, p, and M are numbers (scalar value) instead of matrices. What is the value of T i ...

1what is an electric dipole how is its strength defined2

1.What is an electric dipole? How is its strength defined? 2. What are the different kinds of polarization in a dielectric? 3. What is the polarization vector? How is it related to the electric field intensity? 4. Discus ...

1 distinguish between voltage as applied to time-varying

1. Distinguish between voltage, as applied to time-varying fields, and potential difference. 2. What is a conservative field? Give two examples of conservative fields. 3. Describe the equipotential surfaces for a point c ...

What are the two impairments caused by windowing what

What are the two impairments caused by windowing? What window characteristic is most related to each impairment? How is the effect of each impairment reduced? Can either window impairment be entirely eliminated? Explain ...

A voltage source vt 100 cos2pi50 t v is applied to a

A voltage source v(t) = 100 cos(2π50 t) [V] is applied to a nonlinear load, resulting in non-sinusoidal current: i(t) = 4 + 10 cos(2π50 t +30°) + 20 cos (4π50 t +45°) [A]. Determine: (a) the power absorbed on the load, ( ...

For the flow described in problem obtain the differential

For the flow described in Problem, obtain the differential equation of motion if v θ  = f(r; t). Problem:- The device in the schematic diagram below is a viscosity pump. It consists of a rotating drum inside of a station ...

1 considering te modes in a dielectric slab guide specify

1. Considering TE modes in a dielectric slab guide, specify the fundamental mode and discuss the associated cutoff condition. 2. Compare the phenomenon at cutoff in a metallic waveguide with that at cutoff in an optical ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen