Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem1)

• Rod AB is 1040 HR and loops through bracket and is attached to itself

• Pin C is 301 FH SS

• Bracket is 204T4 Al Cast

• Supports are A36

• Loads are as shown (static)

• Strive to avoid custom sizes

• Don’t worry about bending stress of Bracket BCD

Specify bracket thickness, t, for bearing loads.

969_Bearing loads.jpg

problem2) A sphere 1 ft in diameter is moving horizontally at a depth of 12ft below water surface where the water temperature is 50 degrees ferinheigt V max is 1.5 Vo, where Vo is the free stream velocity and occurs at the maximum sphere width. At what speed in still water would cavitation first occur?

problem3) Find out:

(a) the specific volume, in m3/kg, and

(b) the specific enthalpy, in kJ/kg, of propane at 800 kPa and -60°C.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93954

Have any Question? 


Related Questions in Mechanical Engineering

An athlete at high performance inhales of air at 10 atm and

An athlete at high performance inhales of air at 1.0 atm and 298 K at a respiration rate of 32 breaths per minute. If the exhaled and inhaled air contain 15.3 and 20.9% by volume of oxygen respectively, how many moles of ...

1 repeat the preceding problem for air2 an automobile

1. Repeat the preceding problem for air. 2. An automobile crankshaft is 3.175 cm in diameter. A bearing on the shaft is 3.183 cm in diameter and 2.8 cm long. The bearing is lubricated with SAE 30 oil at a temperature of ...

A rectangular brass column is loaded with a load of p 1500

A rectangular brass column is loaded with a load of P = 1500 lb applied 0.45 in off its centroidal axis. Find the longest permissible length L of the column if the deflection of its free end cannot exceed 0.12 in.

Linear motion actuator with feedback controlanalyses and

Linear Motion Actuator with Feedback Control Analyses and Simulations Provide complete mathematical modeling of the system and its components (free body diagrams and differential equations are required). Provide a comple ...

A uniform cantilever beam with triangular cross section is

A uniform cantilever beam with triangular cross section is loaded only due to its own weight (a load uniformly distributed along the length). What is the ratio of the maximum tensile normal stress to the maximum compress ...

In practice how could you measure that much stretch in a

In practice, how could you measure that much stretch in a bolt of this size? The bolt of problem is put in service and its temperature rises to 2508F. How much change in length of the bolt would you expect this increase ...

In order to penetrate a workpiece a tungsten carbide drill

In order to penetrate a workpiece, a tungsten carbide drill bit is subject to a torque of 3.8 Nm and an axial force of 5 kN. Tungsten carbide is very strong (compressive strength 1400 MPa, tensile strength 340 MPa) but a ...

1 an ion with the configuration f 2 enters an environment

1. An ion with the configuration f 2 enters an environment of octahedral symmetry. What terms arise in the free ion, and with which terms do they correlate in the complex? 2. In the strong field case, the configuration d ...

A bar consists of two portions bc and c d of the same

A bar consists of two portions BC and C D of the same material and of the same length L, but of different cross sections. Determine the strain energy of the bar when it is subjected to an axial load P, expressing the res ...

Need a 400 to 500 minimum word essay on 2 articles no

Need a 400 to 500 minimum word essay on 2 articles (No internet, just based on the articles) - You will need to do a compare and contrast essay where you compare an Old HVAC system with a New system and also old refriger ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro