Question a robot arm has natural frequency of 10 hz and a, Ask an Expert

Engineering

Question: A robot arm has natural frequency of 10 Hz and a damping ratio of 0.3 for motions in the vertical plane. Vertical position is denoted by x1 and vertical velocity by x2. The spectral density of velocity disturbances is 10. Calculate and plot P(t) and K(t) for a time interval of 0.2 sec, assuming P(0) = 0 and using the conventional Kalman-Bucy filter equations for the following measurement:

(a) Velocity only, R = 1.

(b) Position only, R = 1.

View complete question

Mechanical Engineering, Engineering

Category:- Mechanical Engineering
Reference No.:- M92274241

Have any Question?Write your Review or question?

Related Questions in Mechanical Engineering

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

Problem - A long pipe (OD = 141.3 mm, ID =131.8 mm, k p = 20 W/m.K) supplies hot pressurized liquid water at 400 K to a heater in a factory. The pipe has an insulation thickness of 100 mm. A new efficient heater replaces ...

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Problem on shaft -assuming no frictional losses a torque of

Problem on Shaft - Assuming no frictional losses, a torque of T = 750lb·in is applied through the shaft of gear F in order to drive the roller chain at point B at a constant speed. The chain sprocket has a pitch diameter ...

1 explain the term critical equipment and provide two clear

1. Explain the term "critical equipment" and provide two clear examples of machinery which falls into this category on board a twin screw motor vessel. 2. Explain the process of Charpy lmpact Testing including sample mar ...

Force exerted by jet on moving cart1 you need to determine

Force Exerted By Jet On Moving cart. 1. You need to determine the velocity of water that comes out from the nozzle of this system. need the equation please formulate the equation. 2. This water will strike a small cart a ...

The aim of the project is to demonstrate certain aspects of

Structural mechanics questions -q1 a 150-lb bucket is

Structural Mechanics Questions - Q1. A 150-lb bucket is suspended from a cable on the wooden frame. Determine the resultant internal loadings on the cross section at D, and at E. Q2. The shaft is supported at its ends by ...

Fluid mechanics assignment - finite control volume analysis

Fluid Mechanics Assignment - Finite Control Volume Analysis and Dimensional Analysis Q1. The wind blows through a 7ft × 10ft garage door opening with a speed of 5 ft/s as shown in the figure. Determine the average speed, ...

Questions -q1 a qualitative estimate of the effect of a

Questions - Q1. A qualitative estimate of the effect of a wind-tunnel contraction (Figure) on turbulent motion can be obtained by assuming that the angular momentum of eddies does not change through the contraction. Let ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

4,153,160 Questions Asked
13,132 Experts
2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Recent Questions

Ask Mechanical Engineering Expert

Engineering

Related Questions in Mechanical Engineering

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

The aim of the project is to demonstrate certain aspects of

Problem on shaft -assuming no frictional losses a torque of

1 explain the term critical equipment and provide two clear

Force exerted by jet on moving cart1 you need to determine

The aim of the project is to demonstrate certain aspects of

Structural mechanics questions -q1 a 150-lb bucket is

Fluid mechanics assignment - finite control volume analysis

Questions -q1 a qualitative estimate of the effect of a

Heat transfer and combustionyou will need graph paper a

Ask Experts for help!!

Looking for Assignment Help?

Why might a bank avoid the use of interest rate swaps even

Describe the difference between zero coupon bonds and

Compute the present value of an annuity of 880 per year

Compute the present value of an 1150 payment made in ten

Compute the present value of an annuity of 699 per year

Follow Us