Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

Problem: How can we post tension a raft foundation? What design procedure should we follow to post tension raft foundation in order to decrease the concrete and steel volume and increase the strength?

Give specific answer in total 1000 words

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M913951
  • Price:- $35

Priced at Now at $35, Verified Solution

Have any Question? 


Related Questions in Civil Engineering

The flexible shaft ab of the wrench is bent into a

The flexible shaft AB of the wrench is bent into a horizontal arc with a radius of 24 in. The two 20-lb forces, which are parallel to the z-axis, are applied to the handle CD, as shown. Determine the combined moment of t ...

A baseball umpires meter has four displays balls strikes

A baseball umpire's meter has four displays: Balls, Strikes, Outs, and Inning. There are four values for the Balls display (0, 1, 2, and 3), three for Strikes (0, 1, 2), three for Outs (0, 1, 2), and ten for Inning (1, 2 ...

Two identical rollerseach of weight 90n are supported by an

Two identical rollers,each of weight 90N are supported by an inclined plane and a vertical wall as shown in fig., determine the reaction at the points of supports A,B,C assuming all the surfaces to be smooth. Also find t ...

A water treatment plant has four clarifiers treating 80 mgd

A water treatment plant has four clarifiers treating 8.0 MGD (0.350 m 3 /sec) of water. Each clarifier is 16 ft (4.88 m) wide, 80 ft (24.4 m) long, and 15 ft (4.57 m) deep. Determine: A. The detention time (hr) B. Overfl ...

The streetlight a is attached to the end of the horizontal

The streetlight A is attached to the end of the horizontal boom ABO. The light, which weighs 100 N, is subjected to a wind load of 20 N acting in the negative y-direction. The forces P and Q represent the tensions in the ...

Consider the three prototype patterns shown in figure e72i

Consider the three prototype patterns shown in Figure E7.2. i. Are these patterns orthogonal? Demonstrate. ii. Use the Hebb rule to determine the weight matrix for a linear autoassociator to recognize these patterns. iii ...

If the uncertainties in temperature and pressure for prob

If the uncertainties in temperature and pressure for Prob. 7.49 are ±1.5?F and ±2 kPa, respectively, what is the uncertainty of the billing if the actual volume flow measurement is exact? Prob. 7.49 A positive-displaceme ...

A divide-by-2 counter has the following specificationdesign

A divide-by-2 counter has the following specification. Design a divide-by-2 (that is, l-bit) counter using only one D flip-flop. You may also include any combinational logic you wish in your design, butry to minimize the ...

In figure e102 two classes of patterns are giveni use the

In Figure E10.2 two classes of patterns are given. i. Use the LMS algorithm to train an ADALINE network to distinguish between class I and class II patterns (we want the network to identify horizontal and vertical lines) ...

Suppose that we have the following three reference patterns

Suppose that we have the following three reference patterns and their targets: Each pattern is equally likely. i. Draw the network diagram for an ADALINE network with no bias that could be trained on these patterns. ii. ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro