Ask Mechanical Engineering Expert

Lots of bridge designs today contain simple geometrical components but are constructed into complex ways to ensure that relevant base and safety loads are catered for. Bridges are multi-material solutions to withstand the static and dynamic loads that are exerted onto them.

This assignment consists of the following sections – all which must be addressed in your final report:

1) Design a bridge that will withstand 4 fully loaded semi-trailers (ex: 2 going in each direction) at the central point, being aware of both static and dynamic loads, the span of the bridge will be 200 meters in length; width is whatever you determine it must be as suitable but limit yourself to two lanes.

2) Use a minimum of 2 materials and a maximum of 5 materials in your design, it can be any currently available material you choose, but you need to justify your selections.

3) You do not need to consider the connection of the bridge to ground, just assume a rigid stable connection.

4) In your report you need to include loading diagrams, stress analysis of at least 4 different sections of geometry using content developed through this subject plus other resources. 2 analyzed sections must be where 2 materials are joining. As well as any engineering drawings that will be required to fully describe the joint.

5) This is a hand calculation based assignment thus no FEA will be accepted.

6) Keep geometry sections to simple, commercially available shapes.

7) All literature must be properly referenced.

This must be done as your own personal piece of work, no group work allowed.

This assignment must be presented as a formal methodical report with clear unambiguous references. All calculations and assumptions must be provided together with a full explanation of all the terms used. This assignment must be typed and in Microsoft Word *.docx format and submitted via DSO. No hand written or hand submitted assignments will be accepted.

Extensions will only be granted if asked for in writing (email) three days before the due date; a maximum of 7 days will be granted if circumstances are valid – having other assignment due is not a valid reason. Students can only ask for one extension for the trimester period – thus if you have an extension for assignment one you are not able to have another extension for assignment 2 unless under very exceptional circumstances. If your assignment is greater than three days late you will receive zero for that assessment task.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M983

Have any Question? 


Related Questions in Mechanical Engineering

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Force exerted by jet on moving cart1 you need to determine

Force Exerted By Jet On Moving cart. 1. You need to determine the velocity of water that comes out from the nozzle of this system. need the equation please formulate the equation. 2. This water will strike a small cart a ...

Mechanical engineering assignment task - solve the given

Mechanical Engineering Assignment Task - Solve the given problem. Task 1 - A spring with a one-turn loop of 40mm mean radius is formed from a round section of wire having 5 mm diameter. The straight tangential legs of th ...

Projectflow processing of liquor in a mineral refining

Project Flow Processing of Liquor in a Mineral Refining Plant The aim of this project is to design a flow processing system of liquor (slurry) in a mineral (aluminum) refining plant. Aluminum is manufactured in two phase ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

Assignment -q1 explain the difference between the

Assignment - Q1. Explain the difference between the metacentric height of a ship during 'Partially Afloat condition and 'Free Floating' condition; aid a sketch to support your answer. Q2. With the aid of sketches, explai ...

Materials behaviour from atoms to bridges assignment -

Materials Behaviour from Atoms to Bridges Assignment - Distributed loads and static equilibrium (Please note: you should show your steps with necessary figures) Q1. Two beam sections are jointed at C and supported at A b ...

Questions -q1 a qualitative estimate of the effect of a

Questions - Q1. A qualitative estimate of the effect of a wind-tunnel contraction (Figure) on turbulent motion can be obtained by assuming that the angular momentum of eddies does not change through the contraction. Let ...

Assignment - machine learning for signal processingproblem

Assignment - Machine Learning for Signal Processing Problem 1: Instantaneous Source Separation 1. As you might have noticed from my long hair, I've got a rock spirit. However, for this homework I dabbled to compose a pie ...

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

Problem - A long pipe (OD = 141.3 mm, ID =131.8 mm, k p = 20 W/m.K) supplies hot pressurized liquid water at 400 K to a heater in a factory. The pipe has an insulation thickness of 100 mm. A new efficient heater replaces ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As