Ask Mechanical Engineering Expert

Part 1 - Write Project Proposal

This assignment requires you to produce a written report pertaining to the topic for research you have chosen for this unit.

Report Structure

You must submit your proposal in electronic form in 12pt font. Maximum report length is 1000 words or 3 pages. Your report may follow a similar structure

1. Title Page (Title, Student Name, Student ID, Date) (Compulsory)
2. Introduction (no more than one page)
3. Background/ Research Questions and Hypothesis
4. Conclusion
6. Bibliography/References

Report Content

Your proposal must address the following key issues:

• What is the area of research?

• What are the research questions?

In addressing each of these questions, you must explicitly state your research questions and summarise your proposal and rationale. Your introduction must contain the following information: a brief outline of the topic being addressed in this work. The background will explain the topic in light of the problem you will address in the research area. The background will also highlight the research questions and your hypothesis on these questions. Your bibliography must conform to the IEEE style for referencing.

Part 2 - Oral Presentation

This assignment requires you to produce an oral presentation on the topic for research you have chosen for this unit.

Presentation Content

The presentation will discuss the chosen topic, it will present the key objectives of the project along with the background and literature review. It will also present the key findings of the project and your conclusions from it.

Presentation Structure

Your report may follow a similar structure

1. Completed Student Declaration (Compulsory)

2. Title Page (Title, Student Name, Student ID, Date) (Compulsory)

3. Introduction (no more than one page)
     • Present the Problem Significance and Purpose of study
4. Aim of the project or Objectives
     • Present the research questions, definitions, assumptions, limitations

5. Literature Review
     • The background on the research project and literature supporting the research questions and the key findings.

6. Key Findings & Critical Analysis
     • The key results obtained from the research and the analysis of the results and do they support the hypothesis proposed in the project proposal.
7. Conclusion

8. Bibliography 

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M91232481

Have any Question?


Related Questions in Mechanical Engineering

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Force exerted by jet on moving cart1 you need to determine

Force Exerted By Jet On Moving cart. 1. You need to determine the velocity of water that comes out from the nozzle of this system. need the equation please formulate the equation. 2. This water will strike a small cart a ...

Mechanical engineering assignment task - solve the given

Mechanical Engineering Assignment Task - Solve the given problem. Task 1 - A spring with a one-turn loop of 40mm mean radius is formed from a round section of wire having 5 mm diameter. The straight tangential legs of th ...

Projectflow processing of liquor in a mineral refining

Project Flow Processing of Liquor in a Mineral Refining Plant The aim of this project is to design a flow processing system of liquor (slurry) in a mineral (aluminum) refining plant. Aluminum is manufactured in two phase ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

Assignment -q1 explain the difference between the

Assignment - Q1. Explain the difference between the metacentric height of a ship during 'Partially Afloat condition and 'Free Floating' condition; aid a sketch to support your answer. Q2. With the aid of sketches, explai ...

Materials behaviour from atoms to bridges assignment -

Materials Behaviour from Atoms to Bridges Assignment - Distributed loads and static equilibrium (Please note: you should show your steps with necessary figures) Q1. Two beam sections are jointed at C and supported at A b ...

Questions -q1 a qualitative estimate of the effect of a

Questions - Q1. A qualitative estimate of the effect of a wind-tunnel contraction (Figure) on turbulent motion can be obtained by assuming that the angular momentum of eddies does not change through the contraction. Let ...

Assignment - machine learning for signal processingproblem

Assignment - Machine Learning for Signal Processing Problem 1: Instantaneous Source Separation 1. As you might have noticed from my long hair, I've got a rock spirit. However, for this homework I dabbled to compose a pie ...

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

Problem - A long pipe (OD = 141.3 mm, ID =131.8 mm, k p = 20 W/m.K) supplies hot pressurized liquid water at 400 K to a heater in a factory. The pipe has an insulation thickness of 100 mm. A new efficient heater replaces ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As