Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Q1.

a) Describe the four classes of the engineering materials.

b) Recognize the class which each of the given materials belong to.

Present your answer in tabular form:

Silicone, plain carbon steel, concrete, chromium, brass, uranium oxide, aluminum oxide, wool, silicon carbide, cermet, neoprene, carbon fiber reinforced plastic, fiberglass, copper and zirconium oxide.

Q2. Two identical sized specimens of materials A and B are made up from the materials which produce stress v strain graphs as described below:

1780_strain graph.jpg

Answer the given problems; also give reasons for your answers.

a) Name the materials which have the highest value of Young’s Modulus of Elasticity?

b) Under identical loads, name the material which will deflect the most?

c) The specimens are arranged in a press as described below, the press moves uniformly, which of the specimens would be under the maximum stress?

197_stress.jpg

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M99841

Have any Question? 


Related Questions in Mechanical Engineering

Why do we often want to create the correct preload in the

Why do we often want to create the correct preload in the bolts when we assemble a joint? Under what conditions is correct preload relatively unimportant? Name at least three factors that can increase the stress in previ ...

Part 1 key engineering terms fill in the blanks -1

Part 1 Key Engineering Terms: fill in the blanks - 1. Phase: a _____________________________________ homogeneous and distinct portion of material system. 2. Degrees of freedom: number of variables that can be changed ___ ...

A series of calibration tests is conducted on a pressure

A series of calibration tests is conducted on a pressure gage. At a known pressure of 1000 psia it is found that 30 percent of the readings are within 1 psia of the true value. At a known pressure of 500 psia, 40 percent ...

A cubical piece of wood with an edge l in length floats in

A cubical piece of wood with an edge L in length floats in the water. The specific gravity of the wood is 0.90. What moment M is required to hold the cube in the position shown? The right-hand edge of the block is flush ...

The force applied to a nut in a nutcracker is larger than

The force applied to a nut in a nutcracker is larger than the force P applied to the handles. Model the top element of the nutcracker as a beam as shown, and find the forcce on the nut as a function of P and lengths a an ...

1 a differential manometer is used to measure the pressure

1. A differential manometer is used to measure the pressure change caused by a flow constriction in a piping system as shown. Determine the pressure difference between points A and B in psi. Which section has the higher ...

The bar shown has a varying cross section and is fixed

The bar shown has a varying cross section and is fixed rigidly at both walls. The crosssectional area of the narrower section is A; the cross-sectional area of the wider section is larger by a factor of m , or m A. Using ...

A solid circular rod of known radius is twisted in a

A solid circular rod of known radius is twisted in a testing machine with a known torque T. Only one strain gage is available. Does each of the test setups below give us enough information to determine the shear modulus ...

An electrical motor is used to operate a carnot

An electrical motor is used to operate a Carnot refrigerator with an interior temperature of 0.00°C. Liquid water at 0.00°C is placed into the refrigerator and transformed to ice at 0.00°C. If the room temperature is 300 ...

How would you identify the best nut factor for your

How would you identify the best nut factor for your application? How much torque would be required to tighten an ASTM A193 Gr. B16 bolt with a 31/4-8 thread to 60% of yield? Why does a wrench create a side load on the bo ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen