Mechanical propertiesultimate tensile strength 310mpa, Ask an Expert

Engineering

Mechanical Properties:

Ultimate Tensile Strength 310MPa, 4500psi

Tensile Yield Strength 276MPa, 40000psi

Modulus of Elasticity 68.9GPa, 10000ksi

Shear Modules 26GPa, 3770ksi

Shear Strength 207MPa, 30000ksi

Poison’s ratio .33

I am interesting in seeing the equations to find the strengths of a aluminium 6061 tube at 36in x 3in x 3in with 1/4in wall. This is more of a review for me. Would like to see the equations at work. For an example, say I am building a device that requires 36in x 3in x3in x 1 /4in wall aluminium 6061 tube and I need to know if it can withstand a 150lbf load on one end while the other is fixed to the ground. I need to display all the equations to proof that this will work.

View complete question

Mechanical Engineering, Engineering

Category:- Mechanical Engineering
Reference No.:- M91249793

Have any Question?Write your Review or question?

Related Questions in Mechanical Engineering

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

Problem - A long pipe (OD = 141.3 mm, ID =131.8 mm, k p = 20 W/m.K) supplies hot pressurized liquid water at 400 K to a heater in a factory. The pipe has an insulation thickness of 100 mm. A new efficient heater replaces ...

Problem on shaft -assuming no frictional losses a torque of

Problem on Shaft - Assuming no frictional losses, a torque of T = 750lb·in is applied through the shaft of gear F in order to drive the roller chain at point B at a constant speed. The chain sprocket has a pitch diameter ...

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Structural mechanics questions -q1 a 150-lb bucket is

Structural Mechanics Questions - Q1. A 150-lb bucket is suspended from a cable on the wooden frame. Determine the resultant internal loadings on the cross section at D, and at E. Q2. The shaft is supported at its ends by ...

The aim of the project is to demonstrate certain aspects of

Life cycle assessmentfor your chosen service eg white

LIFE CYCLE ASSESSMENT For your chosen service (e.g. white board markers), identify two alternatives of getting the service (e.g. brand A, brand B). Choose the most environmentally friendly option by conducting life cycle ...

Question - truss structureconsider the three membered

Question - Truss Structure Consider the three membered planar truss structure shown in the figure below. All members of the truss have identical square cross-sectional area (A) of 25 mm x 25 mm, and Youngs Modulus (E) = ...

Fluid mechanics assignment - viscous flow in pipesq1 as

Fluid Mechanics Assignment - Viscous Flow in Pipes Q1. As shown in the figure below, water "bubbles up" 3 in. above the exit of the vertical pipe attached to three horizontal pipe segments. The total length of the 0.75-i ...

Force exerted by jet on moving cart1 you need to determine

Force Exerted By Jet On Moving cart. 1. You need to determine the velocity of water that comes out from the nozzle of this system. need the equation please formulate the equation. 2. This water will strike a small cart a ...

Assignment - machine learning for signal processingproblem

Assignment - Machine Learning for Signal Processing Problem 1: Instantaneous Source Separation 1. As you might have noticed from my long hair, I've got a rock spirit. However, for this homework I dabbled to compose a pie ...

4,153,160 Questions Asked
13,132 Experts
2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Recent Questions

Ask Mechanical Engineering Expert

Engineering

Related Questions in Mechanical Engineering

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

Problem on shaft -assuming no frictional losses a torque of

The aim of the project is to demonstrate certain aspects of

Structural mechanics questions -q1 a 150-lb bucket is

The aim of the project is to demonstrate certain aspects of

Life cycle assessmentfor your chosen service eg white

Question - truss structureconsider the three membered

Fluid mechanics assignment - viscous flow in pipesq1 as

Force exerted by jet on moving cart1 you need to determine

Assignment - machine learning for signal processingproblem

Ask Experts for help!!

Looking for Assignment Help?

Why might a bank avoid the use of interest rate swaps even

Describe the difference between zero coupon bonds and

Compute the present value of an annuity of 880 per year

Compute the present value of an 1150 payment made in ten

Compute the present value of an annuity of 699 per year

Follow Us