Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) describe what is main function of the lathe in brief?

2) Describe the cutting tool nomenclature for the single point cutting tool with suitable sketch.

3) describe the tool signature with appropriate ex?

4) List the taper turning method on lathe. describe any one of them.

5) Job which is having length of 100mm is to be turned on the lathe. A length of taper is 60mm with 4 larger diameters of taper 30mm and the smaller diameter 20 mm. Determine half taper angles.

6) prepare differences between the NC and CNC machine?

7) Classify the CNC machine as per the following given condition:

a) According to the control system.

b) According to the system feature.

c) According to the tool positioning system.

3) Describe the constructional attributes of CNC lathe?

4) What is meant by the part program? Describe in detail.

5) describe the benefits and drawbacks of CNC machine?

6) Describe any 5 of G code and M code?

7) Describe the twist drill with suitable sketch.

8) Describe the cutting speed in drilling?

9) describe the deep hole drilling and advantages with the help of neat sketch.

10) describe how machine time is determined for drilling?

11) Describe the operation of drilling machine.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912067

Have any Question? 


Related Questions in Mechanical Engineering

Calculate the total lift force on the arctic hut shown

Calculate the total lift force on the Arctic hut shown below as a function of the location of the opening. The lift force results from the difference between the inside pressure and the outside pressure. Assume potential ...

Name several ways by which the loss of initial preload can

Name several ways by which the loss of initial preload can be reduced ? Roughly how much embedment relaxation could we expect from new parts used in a non-gasketed, steel joint? Define elastic interactions. How can elast ...

Hydraulic circuit pressure dropthe hydraulic circuit shown

Hydraulic Circuit Pressure Drop The hydraulic circuit shown involves a pump and four pressure restrictions. Assuming the reservoir is at atmospheric pressure and the flow is at steady-state, determine the gage pressures ...

1 find the change in temperature between stations 1 and 2

1. Find the change in temperature between stations (1) and (2) in terms of the quantities A 1 , A 3 , v 1 , v 3 , c v , and θ. The internal energy is given by c v T. The fluid is water and T 1  =T 3 , P 1  = P 3 . 2. A l ...

Calculate the size h of the two welds required to attach a

calculate the size h of the two welds required to attach a plate to a frame as shown in figure. if the plate supports an inclined force P=50kn. use a factor safety of 3 and yield shear stress of 350 mpa for the weld mate ...

A neighborhood fuel cell power plant is to be designed for

A neighborhood fuel cell power plant is to be designed for an electric power output of 2000 kW with liquid-water product. Estimate the flow rates of hydrogen and oxygen during peak power production, assuming an 80% effic ...

Derive a formula for the minimum energy in the

Derive a formula for the minimum energy in the two-dimensional Using model, if the interaction energy between each spin and each of its eight nearest neighbors is -D. Assume that the model consists of a rectangular array ...

Whats the maximum proof strength in ksi of a j429 gr 8 bolt

What's the maximum proof strength (in ksi) of a J429 GR 8 bolt and that of an ASTM A490 bolt? What's the proof strength of a metric Class 10.9 bolt in MPa? What is the ultimate strength and the yield strength (in MPa) of ...

There are 3 x 103 spheres in a box calculate the number of

There are 3 x 10 3 spheres in a box. Calculate the number of different combinations for the spheres in order to have 1100 spheres in the front third of the box. Assuming that the distribution is normal, calculate the pro ...

A stationary jet engine is shown air with a density of

A stationary jet engine is shown. Air with a density of 0.0805 lb m /ft 3  enters as shown. The inlet and outlet cross-sectional areas are both 10.8 ft 2 . The mass of fuel consumed is 2% of the mass of air entering the ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro