Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) describe any two desirable properties of the hydraulic fluid.
 
2) describe what is meant by the servo value? describe two of its application.

3) Among the hydraulic and pneumatic system which is more robust and Why?

4) List some of the hydraulic fluids which are used in the industrial hydraulic system.

5) List some of the ways of controlling the maximum pressure in the hydraulic system.

6) describe some of the materials that are used for forming the hydraulic fluids.

7) Explian the following with respect to the hydraulic to hydraulic fluids.

(a) Pour point

(b) flash point

8) State some of the advantages and limitations of the pneumatic system.

9) describe the function of actuator in the pneumatic system and Classify them.

10) describe the differential circuit and state some of its applications.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912337

Have any Question? 


Related Questions in Mechanical Engineering

What must the bolts in a shear joint do to prevent its

What must the bolts in a shear joint do to prevent its failure? Describe some of the factors that make it difficult to create an exact and predicted amount of clamping force during assembly? How does an external load on ...

1 according to the equipartition principle what is the

1. According to the equipartition principle, what is the overall energy in J of one mole of water at 1000 K if translational, rotational, and vibrational degrees of freedom are considered? 2. How many equipartition degre ...

Imagine a set of three n2 molecules frozen in a crystal so

Imagine a set of three N2 molecules frozen in a crystal so that no rotation or translation can occur. But there is energy in vibration, which totals E = 3ve , where the vibrational constant e = 2358cm-1 . If we apply the ...

Equipment engineering and design structural failure

Equipment Engineering and Design Structural Failure Problem- Background - A 6 ton pressure vessel - see dimensioned drawing - was being lowered onto a "stillage"or temporary supporting structure for testing outside a fac ...

A rosette composed of three strain gages measures strain at

A rosette composed of three strain gages measures strain at a point on the surface of a flat sheet of annealed stainless steel loaded in plane stress. The strains measured (numbers correspond to strain gages in the figur ...

An isotopically enhanced sample has ndi moles of deuterated

An isotopically enhanced sample has nDI moles of deuterated hydrogen iodide and nHI moles of common HI at 398 K. Comparison of the infrared intensities of the v = 1 S 2 transition inds a ratio of 0.100 for DI molecules ( ...

Calculate the total lift force on the arctic hut shown

Calculate the total lift force on the Arctic hut shown below as a function of the location of the opening. The lift force results from the difference between the inside pressure and the outside pressure. Assume potential ...

A series of calibration tests is conducted on a pressure

A series of calibration tests is conducted on a pressure gage. At a known pressure of 1000 psia it is found that 30 percent of the readings are within 1 psia of the true value. At a known pressure of 500 psia, 40 percent ...

Invent a structure that can completely eliminate the narrow

Invent a structure that can completely eliminate the narrow gate effects. This is known as the fully recessed stepped oxide (FROSOX) whose sidewall oxide is thicker than the gate oxide and they are connected by a step or ...

In practice how could you measure that much stretch in a

In practice, how could you measure that much stretch in a bolt of this size? The bolt of problem is put in service and its temperature rises to 2508F. How much change in length of the bolt would you expect this increase ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro