Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

problem1. Lake Kickapoo, TX, is approximately 12 km in length by the 2.5 km in width.  The inflow for month of April is 3.26 m3/s and outflow is 2.93 m3/s.  The total monthly precipitation is 15.2 cm and evaporation is 10.2 cm.  The seepage is estimated to be 2.5 cm.  Estimate the change in storage throughout the month of April.

problem2. A city has 6 wells in operation to supply 4.5 million gallons for each day. What is this volume in acre-feet? Suppose pumping is evenly distributed, what is the well yield from each well, in gallons for each minute?

problem3. Find out the water level rise in an unconfined aquifer produced by the seasonal precipitation offour (4) inches. The aquifer porosity is 20%. Suppose the aquifer material was completely dry and there are no other inflows or outflows from aquifer. What would the water level rise be if the aquifer material had moisture content of 3 5%?

problem4. Convert to 1000 g/m/ft2 to ft/d and m/s

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M91129

Have any Question? 


Related Questions in Civil Engineering

A new jet engine is being tested in a wind tunnel as

A new jet engine is being tested in a wind tunnel, as illustrated in the following figure. Air, with standard properties at an altitude of 6000 m, enters the engine at a velocity of 275 m/s through a circular intake port ...

Individual assignment- urban drainage designobjectivedesign

Individual Assignment- Urban Drainage Design OBJECTIVE: Design the drainage system (cross-section of channels) for the particular rainfall and given catchment area. OUTCOMES: Design of cross section should be safe for th ...

The drag on a 2-m-diameter satellite dish due to an 80 kmh

The drag on a 2-m-diameter satellite dish due to an 80 km/h wind is to be determined through wind tunnel testing on a geometrically similar 0.4-m-diameter model dish. a. At what air speed should the model test be perform ...

In this classic problem you are to design a single

In this classic problem, you are to design a single finite-state machine S that will be connected in an arbitrarily long one-dimensional string as follows: Each FSM in the string is connected by k wires to its left and r ...

The arm abcd of the industrial robot lies in a vertical

The arm ABCD of the industrial robot lies in a vertical plane that is inclined at 40? to the yz-plane. The arm CD makes an angle of 30? with the vertical. A socket wrench attached at point D applies a 52-lb · ft couple a ...

A pitot tube uses a manometer readout with a fluid having a

A Pitot tube uses a manometer readout with a fluid having a specific gravity of 0.82. The tube is oriented parallel to an airstream at 1 atm, 25?C, having a velocity of 30 m/s. The accuracy of the dynamic pressure measur ...

1 what is the average emc for an enclosed building in

1. What is the average EMC for an enclosed building in southern California? Cite reference. 2. Determine the dressed size, area, moment of inertia, and section modulus for the following members. Give values for both axes ...

The door header in fig 7c supports a dead load of 120 lbft

The door header in Fig. 7.C supports a dead load of 120 lb/ft and a roof live load of 120 lb/ft. Lumber is No. 2 Hem-Fir. C M = 1.0, C t = 1.0, and C i = 1.0. There are no bolt holes at the point of maximum moment. Later ...

The bar abc of negligible weight is supported by a pin at a

The bar ABC of negligible weight is supported by a pin at A and a rope that runs around the small pulley at D and the 20-lb homogeneous disk. Determine the tension in the rope.

If the uncertainties in temperature and pressure for prob

If the uncertainties in temperature and pressure for Prob. 7.49 are ±1.5?F and ±2 kPa, respectively, what is the uncertainty of the billing if the actual volume flow measurement is exact? Prob. 7.49 A positive-displaceme ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen