Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1: A compressor installed at a whalf (for loading the container ships) is able to give 6 bar.g pressure to the pressure receiver. The compressor is moved to a site which is 5000 ft above sea level (atmospheric pressure 0.85 bar.

a) In the mountains, what is the discharge revised discharge pressure (gauge pressure) of the compressor? Supply there is no change in the temperature.

b) Is the supposition of change in temperature valid for computing the discharge pressure of the compressor?

c) The temperature at the whalf is 35 oC and in the mountains is 19 oC, find out the reduction in volumetric output from the compressor?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98290

Have any Question? 


Related Questions in Mechanical Engineering

What is the stiffness of the bolt and the stiffness of the

What is the stiffness of the bolt and the stiffness of the joint? What is the resilience of the bolt and of the joint members? What is the stiffness ratio of this assembly? What is the increase in bolt tension and the de ...

Sketch a joint diagram for a joint in the preloaded

Sketch a joint diagram for a joint in the preloaded condition, before an external load is applied to the joint. Assume that KJ = 5 KB ? We apply 43 ft-lbs of torque to a 3=8-28 2 J429, GR 8 bolt. We believe that the nut ...

1 if we had only a ruler and a clock as measuring devices

1. If we had only a ruler and a clock as measuring devices, how could we measure the density of water? 2. Calculate the height in meters of a column of water that exerts a pressure of 1.00 bar at its base.

If in the system for problem the total drag on the object

If, in the system for Problem, the total drag on the object is measured to be 800 N/m of length normal to the direction of flow, and frictional forces at the walls are neglected, find the pressure difference between inle ...

Whats the maximum proof strength in ksi of a j429 gr 8 bolt

What's the maximum proof strength (in ksi) of a J429 GR 8 bolt and that of an ASTM A490 bolt? What's the proof strength of a metric Class 10.9 bolt in MPa? What is the ultimate strength and the yield strength (in MPa) of ...

Major assignment employment outlook reportin the groups

Major Assignment: Employment Outlook Report In the groups from your previous assignment, research the employment outlook for your future profession. Present your findings as a formal research report that academic advisor ...

If all the states of an ensemble are equally probable then

If all the states of an ensemble are equally probable, then a 0.05 mol sample of an ideal gas at ixed energy in a 1000 cm3 container has a chance of being found in a state where a speciied 1% region of the volume is not ...

An electronic scoreboard is to be installed in a large

An electronic scoreboard is to be installed in a large stadium. Due to the design of the roof structure, the suspending cables will have different lengths, as is shown below. a. Determine a suitable cross-sectional area ...

Projectdesign a tube bank that will increase the

Project Design a tube bank that will increase the temperature of a 1200 CFM flow of air from 35°F to 100°F. Assume a constant pressure of 1atm. Each tube will have a diameter of 0.5in and a length of 24in. The tube confi ...

1 how large as a fraction of the supported weight w must

1. How large (as a fraction of the supported weight W) must the weight w of the forearm and hand be to change the analysis done under the assumption of weightlessness? 2. What sort of simple measurement or experiment cou ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro