Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1) Interface the 8 bit ADC 808 to port A. Derive control signals from port C.

(a) prepare down the 8086 assembly program segment to read the analog signal.

(b) Interface the 8 bit DAC 08 to port A. prepare down the 8086-assembly program segment to output a ramp.

problem 2)(a) prepare down difference between minimum and maximum modes of 8086? How are these modes selected?

(b) Describe the concept of pipelining in 8086. What are its advantages and disadvantages?

problem 3)(a) Sketch the structure of 8086 flag register and describe the function of the flags with suitable exs.

(b) Describe the functions of following 8086 signals.

1) HLDA

2) RQ/GTO

3) DEN

4) TEST

5) LOCK

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M99527

Have any Question? 


Related Questions in Electrical & Electronics

An infinite plane sheet lying in the plane carries a

An infinite plane sheet lying in the plane carries a current of uniform density Find the magnetic field intensities adjacent to the sheet and on either side of it. What is the polarization of the field?

The rate at which metallic ions are electroplated from a

The rate at which metallic ions are electroplated from a dilute electrolytic solution onto a rotating disk electrode is usually governed by the mass diffusion rate of ions to the disk. This process is believed to be cont ...

1 complete the missing steps in the evaluation of the

1. Complete the missing steps in the evaluation of the integral in equation (9.39a). 2. Find the time-average power required to be radiated by a half-wave dipole in order to produce an electric field intensity of peak am ...

The pressure rise across a pump p this term is proportional

The pressure rise across a pump P (this term is proportional to the head developed by the pump) may be considered to be affected by the fluid density ρ, the angular velocity ω, the impeller diameter D, the volumetric rat ...

Question 1a for the circuit shown in figure 1 sketch the

Question 1. (a) For the circuit shown in FIGURE 1 sketch the voltage waveform across the secondary winding of the transformer. On the same diagram sketch the load voltage waveform. The sketches should take into account d ...

The electric and magnetic fields of a uniform plane wave

The electric and magnetic fields of a uniform plane wave propagating in a perfect dielectric medium are given by Find the permittivity and the permeability of the medium.

The size d of droplets produced by a liquid spray nozzle is

The size d of droplets produced by a liquid spray nozzle is thought to depend upon the nozzle diameter D, jet velocity V, and the properties of the liquid ρ, μ, and σ. Rewrite the relation in dimensionless form. Take D, ...

The single-phase full-bridge inverter from fig 62a has a

The single-phase full-bridge inverter from Fig. 6.2a has a square-wave voltage across a series R-L load. The switching frequency is 50 Hz, the DC input voltage is 250 V, and the load is a serial connection of R = 10 Ω an ...

1 discuss the concept of unit and group patterns and their

1. Discuss the concept of unit and group patterns and their multiplication to obtain the resultant pattern of an array. 2. Distinguish between broadside and endfire radiation patterns. 3. Discuss the concept of an image ...

A periodic signal xt is expressed by the following fourier

A periodic signal x(t) is expressed by the following Fourier series: a. Sketch the amplitude and phase spectra for the trigonometric series. b. By inspection of spectra in part (a), sketch the exponential Fourier series ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen