Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1: In brief show the Organizational chart of the Mechanical engineering department in the Zonal Headquarter.

problem 2: In brief illustrate the Organizational chart of Mechanical engineering department in the Railway Board.

problem 3: In brief illustrate the Organizational chart of Mechanical engineering department in the Division.

problem 4: What are the different duties of Chief Workshop Engineer?

problem 5: What are the various responsibilities of the Chief Mechanical Engineer (Planning)?

problem 6: What are the different duties of the CMPE (Diesel)?

problem 7: Which department co-ordinates the M&P Program and which agency deals with the centralized procurement of the M&P?

problem 8: Name the main departments in a Workshop?

problem 9: In brief describe the difference in the wheel arrangements of CO-CO and B-B Bogies.

problem 10: In brief describe the difference in the wheel arrangements of WDM2 and WDS4 Locos.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M97705

Have any Question? 


Related Questions in Mechanical Engineering

The total pressure of a mixture of oxygen and hydrogen is

The total pressure of a mixture of oxygen and hydrogen is 1.65 atm. The mixture is ignited and the water is removed. The remaining gas is pure hydrogen and exerts a pressure of 0.190 atm when measured at the same values ...

You have been introduced to a number of different tools

You have been introduced to a number of different tools that can be used to help IE's and MfgE's analyze and develop solutions to make processes more effective and efficient. Watch the video located at http://www.iienet2 ...

As can often be seen in a kitchen sink when the faucet is

As can often be seen in a kitchen sink when the faucet is running, a high-speed channel flow (v 1 , h 1 ) may ''jump'' to a low-speed, low-energy condition (v 2 , h 2 ). The pressure at sections 1 and 2 is approximately ...

A series of calibration tests is conducted on a pressure

A series of calibration tests is conducted on a pressure gage. At a known pressure of 1000 psia it is found that 30 percent of the readings are within 1 psia of the true value. At a known pressure of 500 psia, 40 percent ...

A steel bar of 100mm length tapers from 12mmtimes10mmfrom

A steel bar of 100mm length tapers from 12mm×10mmfrom one end to 30mm×20mm at the other. If the stress in the bar is not to exceed 100mpa,find the magnitude of the axial force. Also find the change in its length. Take E ...

For the bar in problem 1112 find the largest allowable

For the bar in Problem 11.12, find the largest allowable value of P if the allowable compressive stress is 250 MPa. Problem 11.12: A steel bar with the cross section shown and effective length L = 2.5 m is subjected to a ...

Describe the mil-std-1312 nas test name three generic ways

Describe the MIL-STD-1312 (NAS) test? Name three generic ways to prevent or at least minimize self-loosening? Define prevailing torque? A proper length-to-diameter ratio for the bolt can reduce or eliminate self-loosenin ...

1 at 60degc the surface tension of water is 00662 nm and

1. At 60°C the surface tension of water is 0.0662 N/m and that of mercury is 0.47 N/m. Determine the capillary height changes in these two fluids when they are in contact with air in a glass tube of diameter 0.55 mm. Con ...

Problem -a consider a one-component system consisting of

Problem - a. Consider a one-component system consisting of spherical bubbles of vapor inside a liquid, which is commonly observed as a liquid begins to boil. This is similar to the case considered in class in which liqui ...

Name at least three reasons why some bolts fail

Name at least three reasons why some bolts fail mechanically? What is the most common cause of bolted joint misbehavior or failure? Name at least two problems that can be caused by overtightening the bolts? What do we me ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen