Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) What are two basic types of internal combustion engines? prepare down the fundamental differences between the two?

problem 2) Draw Ericsson cycle on P-V and T-S diagram.

problem 3) What do you understand by delay period? Describe in detail.

problem 4) Which has a higher sped, a SI engine of a CI engine? Why?

problem 5) How SI engines fuels are rated?

problem 6) Why very rich mixture is required for Idling?

problem 7) Describe the requirements of an Ideal injection.

problem 8) Why supercharging of CI engines is done?

problem 9) What are the different methods for measurement of brake power?

problem 10) SI engines are made of smaller size, describe why in detail?

problem 11) Describe in detail (a) Indicated thermal efficiency. (b) Mechanical efficiency and Brake thermal efficiency. What is the relation between the three?

problem 12) In an Otto cycle at 15° and 1.05 bar is compressed adiabatically until the pressure is 13 bar. Heat is added at constant volume until the pressure rises to 35 bar. Compute air standard efficiency, the compression ratio and mean effective pressure for the cycle. Take CV= 0.718, R= 0.287.

problem 13) What is the significance of delay period? Should the delay period be zero? Describe variable effecting the delay period.

problem 14) Describe the working of single jet carburetor with appropriate sketch. prepare down its limitations? Describe in detail.

problem 15) Sketch value timing diagram of two stroke and four engines and compare them with the actual.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98903

Have any Question? 


Related Questions in Mechanical Engineering

Let the texturized si floating gate be modeled by

Let the texturized Si floating gate be modeled by semi-spherical hills. Calculate the radius of the hemisphere that would increase the write/erase time by 100 over the flat poly-Si/SiO2 interface. Use the Fowler-Nordheim ...

For the allen wrench of problem 715 what is the deflection

For the allen wrench of Problem 7.15, what is the deflection of the tip of the wrench when the maximum load of 60 N is applied, just before the bolt loosens? Problem 7.15: The maximum force applied to the tip of the alle ...

1 in more than one paragraph but less than a page discuss

1. In more than one paragraph but less than a page, discuss some of the failure modes experienced in the collapse of the World Trade Center and how they might have been prevented. 2. A truss ABC supports a load W at join ...

1 find the change in temperature between stations 1 and 2

1. Find the change in temperature between stations (1) and (2) in terms of the quantities A 1 , A 3 , v 1 , v 3 , c v , and θ. The internal energy is given by c v T. The fluid is water and T 1  =T 3 , P 1  = P 3 . 2. A l ...

The lateral base resistance is a fundamental limitation of

The lateral base resistance is a fundamental limitation of high-frequency and high speed performance of BJTs. At low temperatures, deionization of the dopant impurity could increase the base resistance much more than the ...

Assume that the level of water in the tank remains the same

Assume that the level of water in the tank remains the same and that there is no friction loss in the pipe, entrance, or nozzle. Determine (a) The volumetric discharge rate from the nozzle; (b) The pressure and velocity ...

In adiabatic demagnetization we use a magnetic ield to

In adiabatic demagnetization, we use a magnetic ield to couple away almost all of the residual energy of a crystal that has been cooled to 2.2 K by liquid helium. (We can get below the normal boiling point of liquid heli ...

A 15 m tall utility pole is located at a 40deg bend in a

A 15 m tall utility pole is located at a 40° bend in a set of power lines. The tension in each line is 15 kN, and due to sag of the lines, the tension forces act along directions 10° below horizontal. A guy wire has been ...

During the test of a centrifugal pump a bourdon pressure

During the test of a centrifugal pump, a Bourdon pressure gage just outside the casing of the 12-in.-diameter suction pipe reads 6 psig (i.e., vacuum). On the 10-in. -diameter discharge pipe another gage reads 40 psig. T ...

A potential flow source having an intensity of 10m2s placed

A potential flow source having an intensity of 10m2/s, placed in the point of Cartesian coordinates (1;0), and a sink having identical intensity, placed in the point (-1;0), are combined with a uniform flow at 25 m/s, in ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen