Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) Specify some of the elements of the power system?

2) Describe the difference between 3 phase 3 wire and 3 phase 4 wire distribution systems?

3) Provide an expression for capacitance of each conductor of single phase overhead line if there is effect of the earth.

4) describe the drawbacks of the corona?

5) How the capacitance effects are taken into the account in a long transmission line?

6) Specify the units of ABCD constants and provide the relation between those constants?

7) describe the benefits of the underground cables within the distribution systems?

8) describe the benefits of the suspension type insulators over the pin type insulators?

9) Imply any two causes for the case of over voltages.

10) describe how do earthing screen offer protection against the direct lightning strokes?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M913274

Have any Question? 


Related Questions in Electrical & Electronics

1 when is it meaningful to attribute a group velocity to a

1. When is it meaningful to attribute a group velocity to a signal comprised of more than two frequencies? Why? 2. Discuss the propagation of a narrow-band amplitude modulated signal in a dispersive channel. 3. Discuss t ...

A source of strength 15 m2s at the origin is combined with

A source of strength 1:5 m 2 /s at the origin is combined with a uniform stream moving at 9 m/s in the x direction. For the half-body which results, find (a) The stagnation point; (b) The body height as it crosses the y ...

The spacing a between the plates of a parallel-plate

The spacing a between the plates of a parallel-plate waveguide is equal to 5 cm. The dielectric between the plates is free space. If a generator of fundamental frequency 1800 MHz and rich in harmonics excites the wavegui ...

Consider a plane-strain square element with unit depth as

Consider a plane-strain square element with unit depth as shown in the figure. Use the St. Venant-Kirchhoff isotropic material model with two Lame's constants λ and μ. A uniformly distributed force T x  (force per area) ...

1 the rocket nozzle shown below consists of three welded

1. The rocket nozzle shown below consists of three welded sections. Determine the axial stress at junctions 1 and 2 when the rocket is operating at sea level. The mass flow rate is 770 lb m /s. 2. The pressure on the con ...

Uing the laws for the addition of vectors and equation

Using the laws for the addition of vectors and equation (), show that in the absence of gravity, (a) The fluid acceleration, pressure force, and viscous force all lie in the same plane; (b) In the absence of viscous forc ...

1 a program for encoding and decoding lzw compression2 a

1. A program for encoding and decoding LZW compression. 2. A program for encoding and decoding arithmetic compression. 3. A program that reads a two-dimensional matrix of size N × N and writes the values using zigzag ord ...

1 what is an anisotropic dielectric material2 when can an

1. What is an anisotropic dielectric material? 2. When can an effective permittivity be defined for an anisotropic dielectric material? 3. Briefly describe the phenomenon of magnetization. 4. What is a magnetic dipole? H ...

Referring to the figure assume the flow to be frictionless

Referring to the figure, assume the flow to be frictionless in the siphon. Find the rate of discharge in cubic feet per second, and the pressure head at B if the pipe has a uniform diameter of 1 in. How long will it take ...

1 implement the half adder circuit on the breadboard2

1. Implement the half adder circuit on the breadboard. 2. Implement the full adder circuit on the breadboard. 3. Using the 2-bit adder presented in the chapter as a model, implement a 4-bit adder in Logisim. Implement an ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen