Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

Illustrate the following:

i. Hard soldering

ii. Soft soldering.

problem 2:

Illustrate with neat diagram the torch technique of soldering?

problem 3:

prepare brief notes on following weld defects.

(a) Porosity

(b) Under cutting

(c) Cracks.

problem 4:

Why is cleaning of metal is significant for successful welding? Discuss?

problem 5:

Illustrate the metallurgical effects in resistance welding cycle?

problem 6:

Illustrate the process of welding gray cast iron using manual metal arc welding?

problem 7:

prepare brief notes on following:

(a) Shielding gas in arc welding.

(b) Fluxes in arc welding.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M910801

Have any Question? 


Related Questions in Mechanical Engineering

Whats the maximum proof strength in ksi of a j429 gr 8 bolt

What's the maximum proof strength (in ksi) of a J429 GR 8 bolt and that of an ASTM A490 bolt? What's the proof strength of a metric Class 10.9 bolt in MPa? What is the ultimate strength and the yield strength (in MPa) of ...

Derive a counterpart for the case of plane strain in the

Derive a counterpart for the case of plane strain in the xz-plane of the compatibility equation shown in Problem 4.15 for plane stress. How does this plane strain result differs from the compatibility equation for plane ...

1 if the design load is 90 kn 20300 lbf what is the dead

1. If the design load is 90 kN (20,300 lbf), what is the dead load and what is the intensity of the dead load in the light of the live load calculation of Problem CS1.1? 2. Determine the specific weight of lightweight co ...

Engineering skills project brief flume Engineering Skills Project Brief: Flume Ride

Engineering Skills Project Brief: Flume Ride Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers nee ...

An i-beam with the proportions shown is to be used as a

An I-beam with the proportions shown is to be used as a long column. There is a concern about buckling, so two reinforcing plates are to be welded along the length of the column. Two options for the resulting cross secti ...

This atomic force microscope probe is a silicon beam and

This atomic force microscope probe is a silicon beam and tip. The beam is 40 µm wide, 4 µm thick, and 130 µm long. The tip is set back 15 µm from the end of the cantilever. The deflection of the tip is 1 µm for every 42 ...

Obtainand research literture on automotive fuel additives

Obtainand research literture on automotive fuel additives and their properties and prepare a typed 2 page report on your findings. -are they worth the money or are they a waste of time? -do they work? -how? -what is your ...

Each wood railroad tie supports part of the weight of a

Each wood railroad tie supports part of the weight of a train (plus the relatively small weight of a section of rail). This is modeled with two point loads representing the force of the rail on the tie. The reaction from ...

1 the hypodermic needle shown below contains a liquid serum

1. The hypodermic needle shown below contains a liquid serum (ρ = 1 g/cm 3 ). If the serum is to be injected steadily at 6 cm 3  /s, how fast should the plunger be advanced (a) if leakage in the plunger clearance is negl ...

Wat is the resilience of the bolts and joint this time

What is the resilience of the bolts and joint this time? What is the stiffness ratio of this eccentric joint? By how much does the tensile load of 7.40 kips increase the tension in the bolts and reduce the clamping force ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro