Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1: What are the fundamental differences between the CRT, BOX and BOXN wagon?

problem 2: describe the Air brake system of a BOXN Wagon. What are the different parts? What are the benefits of air brake over the vacuum brake system?

problem 3: What are the parts under the control of a Production Engineer (P.E.) in a workshop? Describe in brief, the responsibilities of different sections.

problem 4: Illustrate the typical organizational structure of a workshop? What is the responsibility of a Production Engineer?

problem 5: In brief describe bathtub curve group replacement and its application to preventive maintenance schedule on Railways?

problem 6: Please describe the organization of a workshop.

problem 7: What are the different rests that a Loco Pilot is entitled to?

problem 8: What do you mean by the term crew lobby? What registers and records are kept in the lobbies?

problem 9: Describe the basis on which the crew links are made up of.

problem 10: What protections are taken by crew controller throughout signing on and signing off of a loco pilot? What registers are filled or seen by a loco pilot throughout signing on and signing off?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M97722

Have any Question? 


Related Questions in Mechanical Engineering

An aluminum e 70 gpa cantilever must carry an end load of

An aluminum (E = 70 GPa) cantilever must carry an end load of 1.4 kN as shown. However, in this design, when the beam is loaded the end of the cantilever A has to have the same elevation as point C (i.e., the net deflect ...

Describe the mil-std-1312 nas test name three generic ways

Describe the MIL-STD-1312 (NAS) test? Name three generic ways to prevent or at least minimize self-loosening? Define prevailing torque? A proper length-to-diameter ratio for the bolt can reduce or eliminate self-loosenin ...

1 at 60degc the surface tension of water is 00662 nm and

1. At 60°C the surface tension of water is 0.0662 N/m and that of mercury is 0.47 N/m. Determine the capillary height changes in these two fluids when they are in contact with air in a glass tube of diameter 0.55 mm. Con ...

1 a square gate 4 m by 4 m is located on the 45deg face of

1. A square gate, 4 m by 4 m, is located on the 45° face of a dam. The top edge of the gate is 8 m below the water surface. Determine the resultant force of the water on the gate, and the point through which it acts. 2. ...

The vibrational constant for the non-degenerate inversion

The vibrational constant for the (non-degenerate) inversion or "umbrella" motion of NH3 is 950cm-1 . Calculate the percentage of NH3 molecules in a sample at 373 K that will be in the v = 1 state of the inversion mode.

Electrical current is passed through a resistor immersed in

Electrical current is passed through a resistor immersed in a liquid in an adiabatic container. The temperature of the liquid is varied by 1°C. The system consists solely of the liquid. Does heat or work flow across the ...

A w10 times 45 beam is made of structural steel and used as

A W10 × 45 beam is made of structural steel and used as a column with a length 15 ft. If its ends are fixed, can the column support the critical load without yielding? (Thedesignation W10 × 45 provides specifications abo ...

The tires of the 4555-lb sedan are 65 in wide figure p510

The tires of the 4555-lb sedan are 6.5 in. wide (Figure P5.10). Each tire contacts the ground over a distance of 4.25 in. as measured along the vehicle's length. Calculate the compressive stress between each tire and the ...

In problem compute the upward force on the device from

In Problem, compute the upward force on the device from water and air. Use the results of Problem as well as any other data given in that problem that you may need. Explain why you cannot profitably use Bernoulli's equat ...

The number of molecules crossing a unit area per unit time

The number of molecules crossing a unit area per unit time in one direction is given by where n is the number of molecules per unit volume and v is the average molecular velocity. As the average molecular velocity is app ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen