Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1: For an antenna half power beam width is 3 and scan rate is 30 /sec. Compute the target illumination period. If Runamb = 100 Km. Compute the number of received pulses every illumination period.

problem 2: How is multiple time around echoes distinguished from the unambiguous echoes?

problem 3: What do you mean by the term false alarm?

problem 4: Define the term radar cross section of target.

problem 5: How does integration of the radar pulses enhance the detection capability of the radar?

problem 6: In a radar receiver Pfa = 1.05*10 - 10BIF = 1 MHz. Determine the average false alarm time tolerable? For the same Pfa, how many dbs above the rms voltage, the threshold voltage must be?

problem 7: Describe the importance of radar cross section of targets.

problem 8: Illustrate the operating frequency, power requirements and expected range of an actual radar system.

problem 9: The noise entering the IF amplifier is white Gaussian. If threshold to noise ratio is 14 dB, determine the probability of false alarm?

problem 10: Why do we choose higher radar frequencies for the meteorological radars?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M97510

Have any Question? 


Related Questions in Electrical & Electronics

1 consider three equally spaced sources of strength m

1. Consider three equally spaced sources of strength m placed at (x, y) = ( a, 0),(0, 0), and (a, 0). Sketch the resulting streamline pattern. Are there any stagnation points? 2. Sketch the streamlines and potential line ...

A bug starts at a point and travels 1 m northwardm

A bug starts at a point and travels 1 m northward, m eastward, m southward, m westward, m northward, and so on, making a 90°-turn to the right and halving the distance each time. (a) What is the total distance traveled b ...

Consider the problem of performing system identification as

Consider the problem of performing system identification as shown previously in Figure 9.49. Suppose the system to be identified is the following IIR filter. Write a MATLAB program that uses the FDSP toolbox function f l ...

A certain communication channel has a bandwidth of 10 khz a

A certain communication channel has a bandwidth of 10 kHz. A pulse of 0.5 ms duration is transmitted over this channel. a. Determine the width (duration) of the received pulse. b. Find the maximum rate at which these pul ...

1 find two differential length vectors tangential to the

1. Find two differential length vectors tangential to the surface at the point (2, 4, 1) and then find a unit vector normal to the surface at that point. 2. A hemispherical bowl of radius 2 m lies with its base on the xy ...

1 how many points can we have in a dht with m 102 explain

1. How many points can we have in a DHT with m = 10? 2. Explain the problems we encounter if we use IP addresses as the node identifiers in a DHT. 3. Explain two strategies used for storing an object in DHT-based network ...

1 what are the names of the protocols discussed in this

1. What are the names of the protocols, discussed in this chapter, that provide security for e-mail? 2. How does PGP create a set of security parameters? 3. What is the purpose of the Handshake Protocol in SSL? 4. What i ...

Data at a rate of 1 million pulses per second are to be

Data at a rate of 1 million pulses per second are to be transmitted over a certain communications channel. The unit step response g(t) for this channel is shown in Fig. P2.7-1. a. Can this channel transmit data at the re ...

1 a synchronous alternator is supplying 09 pu power to the

(1) A synchronous alternator is supplying 0.9 p.u. power to the grid when a temporary three-phase short occurs on the interconnector. The power angle curves are:- Pre-fault = 2.0 sin(delta) During fault = 0.5 sin(delta) ...

If the shock-wave velocity in problem is approximated by

If the shock-wave velocity in Problem is approximated by the speed of sound, determine the pressure change causing a velocity change of 10 fps in (a) air at standard conditions; (b) water. Problem:- The shock wave illust ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen