Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

Categorize the degassing processes.

problem 2:

Illustrate about vacuum raising equipment.

problem 3:

Discuss ladle degassing with gas stirring with the aid of a figure.

problem 4:

Make a distinction between the different continuous casting of steel processes.

problem 5:

Illustrate the effect of Manganese content on the type and characteristic properties of the slags formed.

problem 6:

Illustrate about

i. Basicity and

ii. Oxidising power of slags.

problem 7:

Make a distinction between acid iron and basic iron.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911256

Have any Question? 


Related Questions in Mechanical Engineering

What must the bolts in a shear joint do to prevent its

What must the bolts in a shear joint do to prevent its failure? Describe some of the factors that make it difficult to create an exact and predicted amount of clamping force during assembly? How does an external load on ...

A water-filled u-tube manometer is used to measure the

A water-filled U-tube manometer is used to measure the pressure inside an air tank. The water level in the U-tube on the side connected to the tank is 5 ft above the base of the tank. The water level in the other side of ...

The force applied to a nut in a nutcracker is larger than

The force applied to a nut in a nutcracker is larger than the force P applied to the handles. Model the top element of the nutcracker as a beam as shown, and find the forcce on the nut as a function of P and lengths a an ...

1 a cylindrical pressure vessel with hemispherical endcaps

1. A cylindrical pressure vessel with hemispherical endcaps has radius r = 2 m, wall thickness t = 10 mm, and is made of steel with yield stress σy = 1800 MPa. It is internally pressurized at p = 2 MPa. Compare the Tresc ...

A dam discharge into a channel of constant width as shown

A dam discharge into a channel of constant width as shown. It is observed that a region of still water backs up behind the jet to a height H. The velocity and height of the flow in the channel are given as v and h, respe ...

Project solve the 3-dimensional steady state heat transfer

PROJECT Solve the 3-dimensional, steady state heat transfer problem for a cartesian system either numerically or analytically. - If you use the numerical method, write a computer code using the finite difference method o ...

On a certain day the barometric pressure at sea level is

On a certain day the barometric pressure at sea level is 30.1 in. Hg, and the temperature is 708F. The pressure gage in an airplane in flight indicates a pressure of 10.6 psia, and the temperature gage shows the air temp ...

Assume that the level of water in the tank remains the same

Assume that the level of water in the tank remains the same and that there is no friction loss in the pipe, entrance, or nozzle. Determine (a) The volumetric discharge rate from the nozzle; (b) The pressure and velocity ...

The tires of the 4555-lb sedan are 65 in wide figure p510

The tires of the 4555-lb sedan are 6.5 in. wide (Figure P5.10). Each tire contacts the ground over a distance of 4.25 in. as measured along the vehicle's length. Calculate the compressive stress between each tire and the ...

A series of calibration tests is conducted on a pressure

A series of calibration tests is conducted on a pressure gage. At a known pressure of 1000 psia it is found that 30 percent of the readings are within 1 psia of the true value. At a known pressure of 500 psia, 40 percent ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro