Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

prepare down the causes and effect of stresses in welds. How do you manage these stresses?

problem 2:

Illustrate the type of electrode materials employed in TIG?

problem 3:

Illustrate the flux materials employed in TIG welding?

problem 4:

Illustrate the different diffusion welding techniques?

problem 5:

Describe in detail the types of flames and flux needed for gas welding of copper and its alloys?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M910809

Have any Question? 


Related Questions in Mechanical Engineering

A 15 m tall utility pole is located at a 40deg bend in a

A 15 m tall utility pole is located at a 40° bend in a set of power lines. The tension in each line is 15 kN, and due to sag of the lines, the tension forces act along directions 10° below horizontal. A guy wire has been ...

Problem -a piston at one end of a gas filled circular tube

Problem - A piston at one end of a gas filled circular tube of area S oscillates with real-valued velocity: U p (t) = U 1 cos(ω 1 t) + U 2 sin(ω 2 t) Note that two oscillation frequencies are present. The other end of th ...

What must the bolts in a shear joint do to prevent its

What must the bolts in a shear joint do to prevent its failure? Describe some of the factors that make it difficult to create an exact and predicted amount of clamping force during assembly? How does an external load on ...

The case study kahiki-foods-case-study critique it and do a

The case study kahiki-foods-case-study CRITIQUE it and do a 10-12 pages report about it their are notes and a presentation done about it that you can use in doing the paper Also their is an example of a different case wh ...

A series of calibration tests is conducted on a pressure

A series of calibration tests is conducted on a pressure gage. At a known pressure of 1000 psia it is found that 30 percent of the readings are within 1 psia of the true value. At a known pressure of 500 psia, 40 percent ...

Calculate the power factor of an electronic system subject

Calculate the power factor of an electronic system subject to a reasonable amount of harmonics given as THD(v) = 1.0%, the displacement factor is 0.92. What would be the calculated error if harmonic components were not t ...

The bar shown has a varying cross section and is fixed

The bar shown has a varying cross section and is fixed rigidly at both walls. The crosssectional area of the narrower section is A; the cross-sectional area of the wider section is larger by a factor of m , or m A. Using ...

Problem 1 -there is a circular combined open and closed

Problem 1 - There is a circular combined open and closed thin-walled section as shown in the figure. (R = 100mm, t = 2mm, S y = 100N) When shear force S y is applied to Web 24, calculate: a) Calculate I xx for the x-axis ...

1 an automobile is driving into a 45-mph headwind at 40 mph

1. An automobile is driving into a 45-mph headwind at 40 mph. If the barometer reads 29 in. Hg and the temperature is 40°F, what is the pressure at a point on the auto where the wind velocity is 120 fps with respect to t ...

Define prying action sketch an alternative joint diagram

Define prying action? Sketch an alternative joint diagram showing the effects of prying action Name at least two things the joint designer can do to reduce prying action? This and the following three questions are all in ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen