Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

Illustrate the concept of dilution specifically in fusion welding of dissimilar metals.

problem 2:

prepare down the different techniques to control dilution? Discuss.

problem 3:

What do you understand by the term nugget? How the size of resistance spot weld is determined?

problem 4:

How does the spot welding diverge from roll spot welding and projection welding?

problem 5:

Illustrate the effect of fast and slow cooling on microstructure of low carbon steel weld metal?

problem 6:

Why is it that residual stress tends to become less of the problem that faster you’re capable to complete the arc welded joint?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M910804

Have any Question? 


Related Questions in Mechanical Engineering

A compute the intrinsic gate delay of the nmost given in

(a) Compute the intrinsic gate delay of the nMOST given in the above problem and also in section 661 at the biasing condition given above. (b) Compute the intrinsic power-delay product. (c) Does the load resistor increas ...

The top figure shows a diagram of the bones and biceps

The top figure shows a diagram of the bones and biceps muscle of a person's arm supporting a mass. The lower figure shows a biomechanical model of the arm, in which the biceps muscle AB is represented by a bar with pin s ...

Hydraulic circuit pressure dropthe hydraulic circuit shown

Hydraulic Circuit Pressure Drop The hydraulic circuit shown involves a pump and four pressure restrictions. Assuming the reservoir is at atmospheric pressure and the flow is at steady-state, determine the gage pressures ...

Two closed rigid water containers with initial temperatures

Two closed, rigid water containers with initial temperatures T A and T B are brought into thermal contact. At equilibrium, the two containers are at the same temperature. Prove that this process has positive ?S and find ...

Midterm examinstruction by default the graduate students

Midterm Exam Instruction: By default, the graduate students are required to answer all the question below. Question 1 part a) and Question 5 are not required for undergraduate students but are bonus problem for undergrad ...

1 a vertical cylindrical tank having a base diameter of 10

1. A vertical cylindrical tank having a base diameter of 10 m and a height of 5 m is filled to the top with water at 20°C. How much water will overflow if the water is heated to 80°C? 2. A liquid in a cylinder has a volu ...

Assigned work clearly indicate all assumptions and

Assigned Work (Clearly indicate all assumptions and references) 1. A 500 m 2 light colored swimming pool is located at (a) normal suburban site, (b) well-sheltered site, where the measured wind speed at 10 m height is 3 ...

An isotopically enhanced sample has ndi moles of deuterated

An isotopically enhanced sample has nDI moles of deuterated hydrogen iodide and nHI moles of common HI at 398 K. Comparison of the infrared intensities of the v = 1 S 2 transition inds a ratio of 0.100 for DI molecules ( ...

A prototype bolt shaft assume a uniform cylinder that is to

A prototype bolt shaft (assume a uniform cylinder) that is to be loaded in tension is made of a stainless steel with a yield strength of 450 MPa and has a safety factor of 3 with respect to yielding for the maximum allow ...

1 using the expression for the gradient in polar

1. Using the expression for the gradient in polar coordinates (Appendix A), find the gradient of ψ(r,θ) when Where is the gradient maximum? The terms A and a are constant. 2. Given the following expression for the pressu ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro